Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Diesel Discussion

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 05-10-2002, 01:24 PM
surfblau's Avatar
neue Dieseler
 
Join Date: Feb 2002
Location: san francisco - immer kalt, immer windig, I want to move
Posts: 382
should I take hood off to put new hood pad on?

I searched the board and couldn't find any notes on this one, so I thought that I would post a question.

Sould I take hood off (the car) to glue the new hood pad on?

It looks like it would be real easy.. two bolts each side on the hinge arm and disconnect the ww nozzle spray.

This would save me from sifting all the toasty old crumbs of the current pad over the engine, but it would really be easier to apply the glue and weight the pad when I apply the new one.

Is there some hidden danger? Like the hinges snapping up and into the windshield? (doesn't seem like it because at 90 degrees the hood seems pretty unloaded).. Or a likelihood of misallignment when reinstalling?

Am I missing something here?

thanks

__________________
84 300TD - 235k - Farbe "Surfblau" bought at 213k
87 300SDL - 131k - Farbe "PimpGold" bought at 115k
00 Klepper Faltboot Expedition Double
Reply With Quote
  #2  
Old 05-10-2002, 01:50 PM
LarryBible
Guest
 
Posts: n/a
I agree with Bill, but I believe that if you are tall enough, or get something to stand on, it would be much easier to glue the new one in place while the hood is in the full up (90 degree) position. It will have less tendency to fall off while the glue is setting.

Good luck,
Reply With Quote
  #3  
Old 05-10-2002, 02:08 PM
JPL's Avatar
JPL JPL is offline
Its All Within Yourself
 
Join Date: Jun 2001
Location: Philadelphia, PA
Posts: 249
Wink An extra set of arms.....

Surfblau:

Excellent tips from two folks that contribute heavily to this forum. I have learned much from both of them.

But, I must say. an extra set of arms comes in very handy when putting on the new pad. I had good luck with a long broom handle or the like when there isn't an extra hand around. Start gluing one side, then, while standing on the front bumper, I kinda propped the broom handle into the engine compartment and wedged it slightly against the 'finished' corner. (the one you just glued), then worked my way around the rest of the hood pad with my now free set of arms. Whole thing took about 1/2 an hour. Keep in mind, I'm a small guy about 5'6" and 150#, so standing on the bumper did not present any issues. Your situation may be different. You might be taller and won't need the 'granny stool'.

Listen to Bill and USE THAT TARP. I was very glad I did. My old pad just about flaked apart on contact. I used a plastic ice scraper to gently help remove the old residue. I would not use metal to scrape off the old glue/pad if I were you.

Have fun with one of the easiest jobs around.

Thanks,
James

TX - luv the Dead-Head/Rainbow/Tie-Dye Benz emblem !
__________________
James

85 300SD 285k
Charcoal Gray/Grey MB-Tex

79 300CD 142000mi "Rabenshwarz"
Black / Black MB-Tex, Burlwood Int. TOTALLED - 10/24/02 --
Reply With Quote
  #4  
Old 05-10-2002, 02:21 PM
Registered User
 
Join Date: Sep 2001
Location: central Texas
Posts: 17,281
you can use a paint roller with 6 ft handle...to press on the pad....
But this is really a two person job at the time of hanging/glueing....Start at the top and roll down the middle to center it ... then roll outward from the top on each side....
Reply With Quote
  #5  
Old 05-10-2002, 02:50 PM
Registered User
 
Join Date: Jun 2000
Location: Saugus, CA USA
Posts: 2,042
It would be a two person job to take the hood off too.
Reply With Quote
  #6  
Old 05-10-2002, 03:49 PM
wilton
Guest
 
Posts: n/a
No need top remove hood. Put a sheet, paint cloth, etc., over the engine, windshield, etc. "Did both of my MB's and son's Bimmer by myself on the cars; even easier with help.
Reply With Quote
  #7  
Old 05-10-2002, 04:35 PM
84300DT's Avatar
Senior Member
 
Join Date: Jan 2002
Location: Mass.
Posts: 2,219
this must be hood pad week!

here's what i did to protect the engine while removing the old hood pad- it turned to dust when touched
lucky the EPA didn't show up

!hood pad was toast!
__________________
1984 300D Turbo - 231k....totalled 11/30/07 RIP
Reply With Quote
  #8  
Old 05-10-2002, 09:23 PM
2.5 TURBO
 
Join Date: Jan 2001
Location: Send me back to Atlanta
Posts: 876
Hood Pad Installation Made Simple

I just replaced the hood pad on my 300D, 3 weeks ago, it was pretty easy. I had the wife help me roll it in. First I took a old sheet and laid it over cold engine, and then removed what was left of old hood pad with a cooking spatula. I folded the sheet up and emptyed it in the trash can. Shake out the sheet and put it back over the engine. Then I sprayed the hood pad and hood with 3M Adhesive (hurry). I started on one side of the car and my wife on the other, and we just rolled and pushed it right on, very simple. It took less than 30 minitutes. Make sure the heat pad is down towards engine. Simple! 3M works great!! I purchased the hood pad from Parts Shop and 3M from ACE hardware.
__________________
2000 Ford 7.3 Powerstroke 4x4
2006 Mazda Tribute
1983 Black 300 D (donated to charity)
1993 Teal 300 D (160K) Sold
"I love the smell of burnt diesel fuel in the morning, it smells like ....VICTORY"

Semper Fidelis
USMC 1973-1976

Last edited by TN-W124 Diesel; 05-10-2002 at 09:29 PM.
Reply With Quote
  #9  
Old 05-10-2002, 09:30 PM
84300DT's Avatar
Senior Member
 
Join Date: Jan 2002
Location: Mass.
Posts: 2,219
your wife helped you!?!

mano man she must be some kind of lady - mine would not even
consider 'helping' to work on the car- jeez forgetaboutit!!!!
__________________
1984 300D Turbo - 231k....totalled 11/30/07 RIP
Reply With Quote
  #10  
Old 05-11-2002, 05:05 PM
Stevo's Avatar
Registered User
 
Join Date: Apr 2002
Location: NW WA
Posts: 6,299
Smile

Just one thing I might add. If your doing it with no help a couple of clamps for wood working,the kind with plastic over the clamping jaws are handy
With the hood at 90 degrees put glue at the top, clamp the top of the new blanket on. Its hanging down now with the top part glued in the right place, now you can take your time and spread the rest of the glue (the pad is folded up out of the way)then just press it down. The job was easy. I would not consider taking off the hood, and dont forget to cover your engine.
__________________


1985 Euro 240D 5 spd 140K
1979 240D 5 spd, 40K on engine rebuild
1994 Dodge/Cummins, 5 spd, 121K
1964 Allice Chalmers D15 tractor
2014 Kubota L3800 tractor
1964 VW bug

"Lifes too short to drive a boring car"
Reply With Quote
  #11  
Old 05-12-2002, 01:54 AM
Registered User
 
Join Date: Jun 2000
Location: Saugus, CA USA
Posts: 2,042
I took the hood off a car once, to unclog the windsheild washers (the only way to get to them )) It took forever to get the hood re-aligned.
Reply With Quote
  #12  
Old 05-12-2002, 08:23 AM
engatwork's Avatar
Registered User
 
Join Date: May 2000
Location: Soperton, Ga. USA
Posts: 13,647
Whenever you remove a hood on a car take a black permanent marker and "mark out" around where the hinge attaches. Use these marks to line the hood up with during installation.

__________________
Jim
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 12:19 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page