Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Search Forums
Reload this Page Search Results
Register ShopForum Gallery FAQ Calendar Today's Posts Search

Showing results 1 to 30 of 30
Search took 0.01 seconds. Search: Posts Made By: R100RSCA
Forum: Diesel Discussion 10-13-2015, 01:54 PM
Replies: 10
Views: 818
Posted By R100RSCA
That makes sense. I saw the actuator tried to...

That makes sense. I saw the actuator tried to move to different directions. More than likely it is the defect actuator or leaking tube. I will bet on tube. Thank you.
Forum: Diesel Discussion 10-13-2015, 03:56 AM
Replies: 10
Views: 818
Posted By R100RSCA
All doors use the same pump, but each door has...

All doors use the same pump, but each door has its own air feed.
Forum: Diesel Discussion 10-13-2015, 03:54 AM
Replies: 10
Views: 818
Posted By R100RSCA
I haven't gone that far. I didn't connect the rod...

I haven't gone that far. I didn't connect the rod to the new actuator. Still it wouldn't expand or retract much.
Forum: Diesel Discussion 10-13-2015, 03:52 AM
Replies: 10
Views: 818
Posted By R100RSCA
Guess I have to remove the passenger side front...

Guess I have to remove the passenger side front door panel to test the new actuator. If it works, then must the air tube. I would be very upset if it is a defect new actuator. By the way, why the...
Forum: Diesel Discussion 10-13-2015, 03:49 AM
Replies: 10
Views: 818
Posted By R100RSCA
Forgot to mention that I just connected the power...

Forgot to mention that I just connected the power and the air tube to the new actuator. I didn't connect any rod to the new actuator at all. It is just hanging there. So there is no resistance from...
Forum: Diesel Discussion 10-12-2015, 01:48 PM
Replies: 10
Views: 818
Posted By R100RSCA
Central lock system problem. Running out of idea

Hi Everyone,

Need help again on my 1994 S350 diesel again. The driver door will not lock or unlock with the remote, but all other three doors and truck lid lock work just fine. The switch that...
Forum: Diesel Discussion 10-03-2015, 07:00 PM
Replies: 8
Views: 1,417
Posted By R100RSCA
Thank you for your help. I have put it back to...

Thank you for your help. I have put it back to where it belongs. Why it is so hard to find a mechanic that can be trusted! Gee...
Forum: Diesel Discussion 10-02-2015, 10:33 PM
Replies: 8
Views: 1,417
Posted By R100RSCA
You might be right, that piece should not be...

You might be right, that piece should not be there. I searched google images, I don't see it in other pictures.
...
Forum: Diesel Discussion 10-02-2015, 10:22 PM
Replies: 8
Views: 1,417
Posted By R100RSCA
I believe that piece is for lifting the engine....

I believe that piece is for lifting the engine. There are two bolts attach this piece to the engine. I thought about removing the metal piece, but not sure it is safe to do so? Why it is interfacing...
Forum: Diesel Discussion 10-02-2015, 08:56 PM
Replies: 8
Views: 1,417
Posted By R100RSCA
W140 S350 Fan Clutch Question??

Hi,

I bought a W140 S350 diesel almost a year ago without knowing it has NO radiator fan and clutch at all. Please don't ask me why because I already feel so dumb now.

So I ordered new plastic...
Forum: Diesel Discussion 09-06-2015, 12:18 AM
Replies: 6
Views: 1,053
Posted By R100RSCA
Thank you for the explanation, I will look into...

Thank you for the explanation, I will look into that route too!
Forum: Diesel Discussion 09-05-2015, 03:28 PM
Replies: 6
Views: 1,053
Posted By R100RSCA
I have two electric auxiliary fans in front the radiator

Those two fans will engage when water temperature reach around 105. I ordered some metal film resistors to modify the coolant temperature sensor so that fan will engage at 92(Got the idea from...
Forum: Diesel Discussion 09-05-2015, 01:47 PM
Replies: 6
Views: 1,053
Posted By R100RSCA
W140 Diesel Radiator Fan Question

I feel really dumb to ask this question... I bought a 1994 W140 diesel about a year ago. Only this summer I found out when going up hills, say about a mile, the temperature will go up to 110 degrees....
Forum: Diesel Discussion 03-01-2015, 01:05 PM
Replies: 13
Views: 1,823
Posted By R100RSCA
Thank you for all your input

Problem solved this morning. I was able to change the filter in ten minutes. Since this is the first diesel car I own, is it normal to see the fresh engine oil (Shell Rotella T6) I put in yesterday...
Forum: Diesel Discussion 03-01-2015, 02:47 AM
Replies: 13
Views: 1,823
Posted By R100RSCA
Weird, I can see the picture myself. I feel so...

Weird, I can see the picture myself. I feel so dumb after seeing your reply. I found few videos on youtube and none of them removed middle shaft. But all of them were on W126 OM603. I will try again...
Forum: Diesel Discussion 02-28-2015, 09:05 PM
Replies: 13
Views: 1,823
Posted By R100RSCA
Cannot remove om603 oil filter cap!

Hi,

I am facing another unexpected problem again on this W140 diesel recently bought. I can't remove the oil filter cap. It hit the firewall and has no space to maneuver, did I miss anything? I...
Forum: Diesel Discussion 02-28-2015, 05:14 PM
Replies: 8
Views: 1,271
Posted By R100RSCA
Unpluged the connector and it was the problem.

I disconnected the connector on the back of the IP. The idle went down to 500 RPM. Engine shakes a little bit but it stays and won't go up to 2000 RPM without press the gas. So I guess that ELR is...
Forum: Diesel Discussion 02-27-2015, 02:31 AM
Replies: 8
Views: 1,271
Posted By R100RSCA
I thought about it too. But it doesn't explain...

I thought about it too. But it doesn't explain why the idle was normal when engine is cold. Idle speed goes up when engine is warmer. If I messed up the throttle linkage, it will goes to 2000 RPM as...
Forum: Diesel Discussion 02-26-2015, 02:03 PM
Replies: 8
Views: 1,271
Posted By R100RSCA
So I should be looking for some plugs at the back...

So I should be looking for some plugs at the back of the IP with wires connected? I will try that when I get back home. Can I drive the car with that cable disconnected if OM603 has one? Thank you.
Forum: Diesel Discussion 02-26-2015, 01:04 PM
Replies: 8
Views: 1,271
Posted By R100RSCA
1994 S350D OM607 Engine Idle Problem

Hi Guys, I searched this forum but I couldn't find the answer so I started a new thread. Thank you in advance for any feedback.

I acquired a used S350D few months ago. Had some hard time to...
Forum: Diesel Discussion 07-23-2014, 02:28 PM
Replies: 24
Views: 5,265
Posted By R100RSCA
I am at Los Angeles, San Fernando Valley. I will...

I am at Los Angeles, San Fernando Valley. I will try to soak it for a day or two. If any member knows a reliable shop can solve my problem with a reasonable price, please PM me. Money is kinda tight...
Forum: Diesel Discussion 07-23-2014, 01:43 PM
Replies: 24
Views: 5,265
Posted By R100RSCA
I will buy PB Blaster and try, but I doubt it...

I will buy PB Blaster and try, but I doubt it will help in my case because the GP still in the hole, it stick out the same length as others. Like the other member said, I may stripe the threads in...
Forum: Diesel Discussion 07-23-2014, 01:42 PM
Replies: 24
Views: 5,265
Posted By R100RSCA
Does that mean I need to find a new head? :eek:

Does that mean I need to find a new head? :eek:
Forum: Diesel Discussion 07-23-2014, 11:32 AM
Replies: 24
Views: 5,265
Posted By R100RSCA
I think I have a broken GP in the hole

I examined the GP again last night, when I tried to turn the nut, the electrode(not sure it is the name) will not spin with the nut. I don't see any part with the threads came out, it still is in the...
Forum: Diesel Discussion 07-22-2014, 11:32 AM
Replies: 24
Views: 5,265
Posted By R100RSCA
Somehow I was thinking about the injector pump...

Somehow I was thinking about the injector pump instead of injector when I see your thread, I don't know why :confused:. After seeing the picture, it makes sense now :) Thank you.
Forum: Diesel Discussion 07-22-2014, 09:42 AM
Replies: 24
Views: 5,265
Posted By R100RSCA
I was able the change the plug on cylinder #2 and...

I was able the change the plug on cylinder #2 and #4 (assume #1 is the closest to grill). #1 is stuck, I haven't touch the rest. Just curious, how do I check pre-chamber without removing the GP?...
Forum: Diesel Discussion 07-22-2014, 09:37 AM
Replies: 24
Views: 5,265
Posted By R100RSCA
Hope it is like you said, I didn't have a chance...

Hope it is like you said, I didn't have a chance to work on the car yesterday. Will compare with other plugs to see if the threaded part has come out all the way. Soaking is mush easier than taking...
Forum: Diesel Discussion 07-21-2014, 06:12 PM
Replies: 24
Views: 5,265
Posted By R100RSCA
Hi Diesel911, Thank you for the link. I...

Hi Diesel911,

Thank you for the link. I think I have to take the head out to do this whole drilling thing, the direction of the GP on om603 makes it impossible to drill while the head is on the...
Forum: Diesel Discussion 07-21-2014, 05:59 PM
Replies: 24
Views: 5,265
Posted By R100RSCA
Thank you all for the replies. I think I didn't...

Thank you all for the replies. I think I didn't make myself clear, I cannot take the glow plug out at all. It will turn with the socket, but it won't come out any further, it stays in the hole as...
Forum: Diesel Discussion 07-21-2014, 12:49 PM
Replies: 24
Views: 5,265
Posted By R100RSCA
Advice needed on removing glow plug (om603.971)

Hi Guys,

I searched the forum before posting a new thread. I couldn't find the right solution for the problem I am having, so any advice would be appreciated.

I purchased a 94 S350 not long ago...
Showing results 1 to 30 of 30

 
Forum Jump


All times are GMT -4. The time now is 11:20 AM.

Contact Us - Mercedes-Benz Discussion Forum - Archive - Privacy Statement - Terms of Service - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2025, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page