Parts Catalog Accessories Catalog Tech Info Tech Forums
  Search our site:    
 Cart  | Project List | Order Status | Help    

Go Back   PeachParts Mercedes ShopForum > Technical Information and Support > Tech Help

LinkBack Thread Tools Display Modes
Old 03-12-2001, 05:58 AM
Posts: n/a
Have a w126 280se 1985 with M110 engine and automatic gearbox

When the engine runs, and I choose any gear with brakes on, the engine stops running!
When I do the same without brakes on I can drive the car till the next stop!
What could be the problem?
Is it possible the engine need to be tuned better?
Earlier I used a (starter-spray) witch give an explosion in the air-cleaner that deformed a little the doser-plate of my KA-JETRONIC, I tried to get it flat again but could not do it for 100%!
Could that be the reason of all my problems?

Thanks for any help
Reply With Quote
Old 03-12-2001, 06:12 AM
Posts: n/a
Is it possible to purchase the dozer-plate separately (BOCH maybe) en what is the order nr

Thanks for your kindness
Reply With Quote
Old 03-12-2001, 07:24 AM
ymsin's Avatar
Driver, Mercedes-Benz
Join Date: Feb 2001
Location: Malaysia
Posts: 1,645
Hmm ... I am dumbfounded by this problem. First time hearing of this. I dont think its a tuning problem. Sounds more like a failure in the power plant.

I do hope someone here would have a lead.

... Kerry

126 tailed by a 203, 129 leading the pack.
Reply With Quote
Old 03-12-2001, 01:43 PM
Posts: n/a
Power plant


It may seem stupid, but what is a power plant?

Thanks for your reply, there is atliest someone who cares!

Reply With Quote
Old 03-12-2001, 02:40 PM
Join Date: Mar 2000
Location: Gainesville FL
Posts: 6,844
I imagine the problem is due to the engine "torquing " over. I would suspect the green wire from the ignition to the ignition control unit. Other possibilities include the air hose for decel leaning and the coil wire.

Does the car die when put into reverse? The engine torques the opposite direction so use this for diagnostics. I would try pulling on all the hoses and harnesses paying close attention to any that are already tight. The engine ground could also be involved.
Steve Brotherton
Continental Imports
Gainesville FL
Bosch Master, ASE Master, L1
33 years MB technician
Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
Basic Automatic Gearbox Knowledge pentoman Tech Help 2 02-21-2004 08:19 AM
280se 3.5 v8 Automatic Gearbox Problem Thunderbubble Vintage Mercedes 12 01-13-2004 04:59 PM
Automatic Gearbox Problems! yel_low Tech Help 0 03-31-2003 04:28 PM
Automatic Gearbox fluid overheat!!! Gary! Tech Help 0 05-25-2002 07:01 PM
Automatic Gearbox noise Gary! Tech Help 0 05-23-2002 10:40 PM

All times are GMT -4. The time now is 06:04 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2011 Pelican Parts - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page