|
|
|
|
|
LinkBack | Thread Tools | Display Modes |
#16
|
|||
|
|||
hi, arthur
what ciruit #15 are you talking about? circuit #15 for ecu or for what module? i am confuse plz explain cuz i have searched and found abs control unit circuit 15 is heading toward the charging system and for computer module it is heading to ward air injection pump? am i looking at right place? |
#17
|
|||
|
|||
key on engine off no i do not have the CE light on - check engine light. i have checked the bulb and it is good.
|
#18
|
|||
|
|||
Do you want to answer my questions at each step?? Forget about circuit5 15 for now..I am trying to get through some test..
I repeat: DO YOU HAVE A CE LAMP with key on/engine off at the dash...yes or no???? |
#19
|
|||
|
|||
no
|
#20
|
|||
|
|||
[QUOTE=usman21;1510413] no
Thank You very much.. Can you handle building this?? http://members.aol.com/ajdalton7/ledtool.jpg |
#21
|
|||
|
|||
k i have finishing making the tool. i went to radio shack yesterday to buy the stuff i need. one question i have is that where do i the middle plug goes to?
|
#22
|
|||
|
|||
Quote:
Go to fuse # 9 and take your test lamp/meter [ whatever you used for the last voltage test] and I want you to test BOTH sides of that fuse..do not touch the fuse ends, but rather the fuse holder connectors..each side ...pos lead to fuse , neg to a good ground. KOEO... |
#23
|
|||
|
|||
Quote:
i am getting 12.22v at engine off and key off. |
#24
|
|||
|
|||
OK
Lets see what you have for codes . Te tool is used the same as the built-in led combo..You use red at pin #16, blk at #1 and use the odd one at pin 8. That will be HFM/SFI engine management module. Get them first and then go get the ones at #14. That should have codes for the ASR/ABS .. We will go back for DM codes later. I want to be sure we can access the others first b/c I suspect your CE lamp module has been diconnected in order to sell you the car w/o a CE Lamp Warning system operating . Meaning they had emmissions fault codes stored and did not want a perspective buyer to know about it. That is why I wanted positive confirmation of fuse #9..that powers the DM CE lamp module.. See what you have at 8 amd 14 , if any |
#25
|
|||
|
|||
hi arthur the led just blink solid does not flash on both system?
just solid and thats it . |
#26
|
|||
|
|||
Quote:
So that I understand you correctly.. you put KOEO--you hooked up tool and went to pin 8-- you pressed the button, it lit and you held the button down for 2/3 secs and released---you waited a couple of secs and nothing came back in Flash Format ???? But it came back as solid 4 sec????? |
#27
|
|||
|
|||
Quote:
and i finally got it thanks to you =) on pin #8 i get code 42 after pressing the button for 2/3 sec it started to flash and it flashed 42 times= code 42? on pin # 14 i got code #5 |
#28
|
|||
|
|||
Did you do it again after those codes to see if there were any more ?
|
#29
|
|||
|
|||
yes i did and i got the same code again.
|
#30
|
|||
|
|||
Ok
If they repeat, that means that is all the codes for those modules. The codes come up in numerical sequence , so any time you go for codes , after one flashes back, repeat the procedure b/c there may be another hiding behind that one , with a higher number of flashes [ ie 4, 7. 9. 12 . etc] You know you are done when the first one repeats. So, you have a problem with the Cruise set switch and you have no cummunication with the DM module. Now , same deal..but this time I want you to go get the codes from pin #3 .That is the same as the built-in led, so that will tell you if it is the DM circuit or the sw/led. I also would like you to try using the built-in led again , as I am now not so sure you knew how to get the codes from before. |
Bookmarks |
|
|