Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 08-05-2001, 08:04 PM
CJ CJ is offline
Registered User
 
Join Date: Jun 2000
Location: Earth
Posts: 1,318
Cleaning fuel guage sending unit

I just cleaned the sending fuel guage sending unit in my 1991 300D 2.5 and I wanted to pass along that the unit is removed through the trunk, not under the back seat, for this particular model. I started by removing the rear seats and removed the plastic 6 inch body plug, but nothing was there aside from the tank itself. I removed the carpeting in the trunk and these she was. I cleaned the tube with brake cleaner to remove all that gooey black stuff, then I soaked the tube in ATF. I put it all back together and now my fuel guage does not dance around like a pin ball flipper.


Reply With Quote
  #2  
Old 08-06-2001, 08:55 AM
G-Benz's Avatar
Razorback Soccer Dad
 
Join Date: Apr 2001
Location: Dallas/Fort-Worth
Posts: 5,711
Nice tip!

Mine is going through the disco dance once I get to the 1/2 full mark, and I wondered if there was a solution other than replacement...I'll check my manual to see if I can get to mine through the trunk as well.
__________________
2009 ML350 (106K) - Family vehicle
2001 CLK430 Cabriolet (80K) - Wife's car
2005 BMW 645CI (138K) - My daily driver
2016 Mustang (32K) - Daughter's car
Reply With Quote
  #3  
Old 08-06-2001, 08:09 PM
CJ CJ is offline
Registered User
 
Join Date: Jun 2000
Location: Earth
Posts: 1,318
What car are you having trouble with? If it is the 300E, I would pull back the single piece of vertical carpeting to see if you can see the sending unit. Mine was dead center on the top of the seat back, looking from inside the trunk. You can even feel it through the carpeting.
Reply With Quote
  #4  
Old 08-06-2001, 09:06 PM
G-Benz's Avatar
Razorback Soccer Dad
 
Join Date: Apr 2001
Location: Dallas/Fort-Worth
Posts: 5,711
It's the 300E. The manual states that it's located in just about the area you described. But I just filled the tank up today, so I won't go about removing it until later in the week.
__________________
2009 ML350 (106K) - Family vehicle
2001 CLK430 Cabriolet (80K) - Wife's car
2005 BMW 645CI (138K) - My daily driver
2016 Mustang (32K) - Daughter's car
Reply With Quote
  #5  
Old 08-06-2001, 10:23 PM
CJ CJ is offline
Registered User
 
Join Date: Jun 2000
Location: Earth
Posts: 1,318
I ws working with diesel which is less flamable than gasoline, so be careful. metal on metal can spark.

Remember, 1 gallon of gasoline can propel 3400 lbs of metal 25 + miles!!!!
Reply With Quote
  #6  
Old 08-06-2001, 11:07 PM
Senior Member
 
Join Date: Mar 2001
Location: Accokeek, MD
Posts: 683
Liquid gasoline does not readily explode. It must first be vaporized and mixed with sufficient amounts of oxygen.

However it will burn proportional to the amount of oxygen reaching the flame.

Not saying that it is not dangerous... only that danger and caution should be in proper perspective.

You can throw a burning cigarette into a bucket of gasoline and the liquid gasoline will extinguish the burning ash... the same as water would.

Don't suggest you try it... just take my word for it. An open flame however will set the gasoline in the bucket afire.... but it will not explode because oxygen can only reach the limited surface of the liguid.
__________________
Earl



1993 190E 2.3
2000 Toyota 4x4 Tundra
Reply With Quote
  #7  
Old 08-07-2001, 10:28 AM
G-Benz's Avatar
Razorback Soccer Dad
 
Join Date: Apr 2001
Location: Dallas/Fort-Worth
Posts: 5,711
True, true...

Gasoline must be atomized in order to burn properly...otherwise, fuel injectors could behave more like anema bladders instead of the sprayers that they are. (Whew, there's a picture!)

Because of all of the fuel vapor present in an almost empty tank, a collision that would breach the fuel tank would likely result in an explosion. This is less likely if the tank were full.

However, CJ, given the fact that I will service the sender with a near-empty tank of gas on a hot Texas summer day, the caution is welcomed. Ventilation is of the utmost importance.
__________________
2009 ML350 (106K) - Family vehicle
2001 CLK430 Cabriolet (80K) - Wife's car
2005 BMW 645CI (138K) - My daily driver
2016 Mustang (32K) - Daughter's car
Reply With Quote
  #8  
Old 08-07-2001, 11:03 AM
Senior Member
 
Join Date: Mar 2001
Location: Accokeek, MD
Posts: 683
Thanks for rounding my thread off GB.
__________________
Earl



1993 190E 2.3
2000 Toyota 4x4 Tundra
Reply With Quote
  #9  
Old 08-07-2001, 06:52 PM
CJ CJ is offline
Registered User
 
Join Date: Jun 2000
Location: Earth
Posts: 1,318
Caution is key, just ask XXXXXXX, in Baltimore MD how a few Porsches took an unexpected flight through the roof of the service building and landed on the main road, 3 weeks ago, becuase of a static electricity spark set off some gasoline. I won't say the name of the dealership, but those who live in Baltimore know that they have a huge empty lot where Porsche's used to sit, but the MBZ, VW, Subaru and Audi building are ok.
Reply With Quote
  #10  
Old 11-08-2002, 08:02 PM
goldstone's Avatar
W126 Lover
 
Join Date: Oct 2002
Location: Dutchess County, New York
Posts: 158
Thumbs up S U C C E S S !!!!!

Some of these old threads are worth their weight in gold!

I'm no great mechanic, but from the straightforward instructions I found in this and related postings on fuel senders, I was able to correctly diagnose and repair my car. I figure it saved me a few hundred bucks; but more importantly, I feel GREAT that I pulled it off (without blowing up the house!!!)

In my case, the problem was varnish deposits and a broken copper wire (the one that carries the "empty" signal to the indicator light on the dash). By CAREFULLY cleaning the device as instructed and then resoldering the broken copper wire back in place, the problems were eliminated.) I got everything back in place with the proper torque, and voila...

This archive is a tremendous resource to Benz owners. Thanks to all of you who share your knowledge and experience so generously. It's really appreciated by those of us that love these cars but lack the same level of expertise!!!

__________________
Eric

1991 560SEL-Euro (214,000 miles)
1989 420SEL (Retired from daily use at 325,000 miles; Use as donor vehicle)
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
300td fuel sending unit filaments coleman kelly Diesel Discussion 8 05-30-2013 12:16 AM
240D fuel tank removal and cleaning dmorrison Diesel Discussion 42 09-25-2010 08:04 PM
Fuel level sending unit question braverichard Diesel Discussion 22 09-05-2007 06:54 AM
Removing fuel sending unit The Warden Diesel Discussion 3 01-12-2003 10:03 PM
Gas gage jeff karg Diesel Discussion 6 05-30-2002 02:08 PM



All times are GMT -4. The time now is 09:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page