|
|
|
|
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
1993 500SL ASR light.........Pulled codes! What do these codes mean?
Car idles fine for around 30 sec. then ASR light comes on and car drops severely in idle and function. What are these codes pointing to?
Pin 4- 4 Pin 6- 10,11,30 Pin 7- 3,5,6,14 Pin 8- 5,6,12 I erased all codes, except on pin 4 I couldn't get it to clear. I restarted the car for a while and let it run. When I retested I had codes Pin 6- 10 and Pin 7- 14. these two codes had already reappeared. My ASR light never went off even after resetting all the codes. All help is very appreciated. |
#2
|
|||
|
|||
Pin # 7 is the cause of the ASR lamp.
Code 3, is pointing to the throttle actuator. Code 5, is for a bad brake lamp switch. Code 6, is for a bad neutral safety switch. Code 14, is about mis-adjusted accelerator cable OR bad switch on the gas pedal.
__________________
MERCEDES Benz Master Guild Technician (6 TIMES) ASE Master Technician Mercedes Benz Star Technician (2 times) 44 years foreign automotive repair 27 Years M.B. Shop foreman (dealer) MB technical information Specialist (15 years) 190E 2.3 16V ITS SCCA race car (sold) 1986 190E 2.3 16V 2.5 (sold) Retired Moderator |
#3
|
|||
|
|||
Wow, you've hit the jackpot. Every single one of those will send a car into "limp home". My car is the poster boy for this problem (still unsolved)
Anziani '93 300CE '95 E420 |
#4
|
||||
|
||||
Here's the codes in "module" format . . "pins" confuse me ..
Module - Pin - Code# - Description LH-SFI -- 4 ---- 4 --- Voltage at mass air sensor with hot wire circuit; open or short circuit Base ---- 8 ---- 5 --- Maximum permissible temperature in module box exceeded --------- 8 ---- 6 --- Electromagnetic a/c compressor clutch blocked --------- 8 --- 12 --- Voltage supply for ABS control module, ABS/ASR control module or ASD control module interrupted ABS ----- 6 --- 30 --- CAN data line to electronic accelerator/cruise control/ idle speed control module EA/CC/ISC 7 ---- 3 --- Right EA/CC/ISC actuator (left cylinder bank) (M16/1) --------- 7 ---- 5 --- Stop lamp switch (S9/1) --------- 7 ---- 6 --- Starter lock-out/backup lamp switch --------- 7 --- 14 --- Closed throttle position contact switch Has the wiring harness been replaced . . ?? If so, it certainly looks like a going bad ETA or supporting 'switches". Also the "LH" voltage is a strange code w/ an ETA failure. You may want to check it out . . . What about a CEL?? Is it not lighted?? If so, check pin 19, there s/b some codes there. Finally, read Menu#24 . . here |
#5
|
||||
|
||||
__________________
91 MBZ 300TE 4M 91 Jag XJS V12 94 Alfa Romeo 164 LS 80 BMW 320i 85 BMW 528e 86 BMW 325e 88 BMW 325e 88 BMW 325i 89 BMW 325ix 95 BMW 525i 96 BMW M3 78 Fiat Spyder 124 98 Land Rover D1 LSE 98 Range Rover HSE 4.6 93 MBZ 190E 2.6 96 MBZ C280 93 MBZ 400E 90 MBZ 300ce 71 MGB-GT 91 VW Corrado G60 97 328i 99 E320 Wagon 97 E320 https://lh3.googleusercontent.com/-t...r+sig+copy.jpg |
#6
|
|||
|
|||
Check the smallest components first (brake switch, etc etc) as any single point of failure on these ASR lights will light up the codes like a christmas tree!
__________________
former: 83 300D, 97 C230, 93 400E current: 08 C300 Luxury , 92 500SL |
#7
|
||||
|
||||
Quote:
I'm getting the same thing (pin #7 3, 5,6, & 14), though no "limp mode" drives normally except doesn't shift right under kick down WOT (wants to stay in that gear). Can't clear ABS/ASR lights with simple 3 wire reader (at pin #7)
__________________
91 MBZ 300TE 4M 91 Jag XJS V12 94 Alfa Romeo 164 LS 80 BMW 320i 85 BMW 528e 86 BMW 325e 88 BMW 325e 88 BMW 325i 89 BMW 325ix 95 BMW 525i 96 BMW M3 78 Fiat Spyder 124 98 Land Rover D1 LSE 98 Range Rover HSE 4.6 93 MBZ 190E 2.6 96 MBZ C280 93 MBZ 400E 90 MBZ 300ce 71 MGB-GT 91 VW Corrado G60 97 328i 99 E320 Wagon 97 E320 https://lh3.googleusercontent.com/-t...r+sig+copy.jpg Last edited by EuroRash; 09-26-2012 at 05:53 PM. |
Bookmarks |
|
|