Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 08-16-2012, 06:20 PM
Registered User
 
Join Date: Oct 2007
Location: Madison, Wis.
Posts: 66
My notes on replacing the exhaust of a W124 wagon (1995 E320)

If interested, here is a rundown on my most recent job, replacing the original exhaust on my 1995 E320 W124 wagon.

The executive summary message: this was not an easy job. I would not attempt it unless you have a lift. You will be wrestling with seized steel, and due to the design, things could get very difficult. It's not just cutting bolts or pipes, it's trying to free an overlapping/fitted exhaust pipe that is connected to the catalytic converter.

OK, more detail.

My replacement exhaust pieces were Bosal (made in Belgium!) and consisted of a front silencer, a rear silencer, a left fitting or gasket, a right fitting or gasket, a 2.5" exhaust clamp, 4 M8 x 60mm bolts and 4 M8 nuts.

The catalytic converter has two pipes leading to the exhaust parts I replaced.
One is a butt joint with flared flanges and a solid metal ring in between that serves as a gasket or seal. They are joined by two sliding rings that bolt together with 2 bolts. The other pipe off the catalytic converter joins the exhaust by overlapping it by 4 to 5 inches. The catalytic pipe is on the inside of this fitting; the exhaust pipe is flared at the end and has a gasket ring made of densely braided wire. Again, this joint has two rings that bolt together with two bolts to push it tight.

These to pipes go to the first silencer, which hangs from one rubber hanger. One pipe joins the pipe of the second silencer or muffler with a common slide-over connection and exhaust clamp.

The 4 bolts to loosen the fittings at the catalytic converter will have difficult access for at least one bolt. Plan on cutting the bolts and at least one pipe to gain better unless you are lucky with heat and PB Blaster.

Similarly, it is not necessary to free the clamp; you can simply cut the pipe between the two silencers.

A sawzall makes this job much easier.

Now, to the truly difficult part: getting the overlapping pipes separated at the catalytic converter.

On my car, which still after 17 years had the original exhaust, this was enormously difficult. I heated and PB blasted the joint several times, used pry bars, an air chisel, various hammers, a plumber's wrench and a 5-foot leverage pipe.

Eventually, it just sort of tore off, leaving a bit of the catalytic pipe that was under the joint.

Ideally, I would have had more pipe to slip into the new steel, but there was just enough to work with to get the wire-braided ring into the joint and everything tight and sealed.

In summary, think twice before taking this on. The drawing or diagram makes it look easy. In reality, you are going to have to work very hard to separate strongly bonded steel, with the risk of ruining the pipe you rely on to make your replacement parts fit.

__________________
___________________________
1995 E320 (2009 - current)
1985 300TD Turbo black (2007-current)
1983 300TD Turbo red (2008-2009)
1972 280SE (2004-2007)
1977 300CD (2003-2004)
1976 240D (1999-2003)
Reply With Quote
  #2  
Old 08-19-2012, 04:44 PM
stormyc88's Avatar
muffled but untamed
 
Join Date: Oct 2010
Location: Babylon, NY
Posts: 160
Great write up!

I did this job last year on the 87 300e, and was just as hard to get the old pipes off as yours, even though my exhaust was only 7 years old. I decided to go with all stainless mufflers from timevalve, and I used all stainless hardware from Totally Stainless. 1 year later, and everything is still nice and shiny!

__________________
Streetside: 1987 Mercedes 300E Petrol Blue/Green
2014 Ford Mustang Grabber Blue
1999 Ford Ranger Green

Dockside: 1968 Eltro 17
1985 Silverton 34C
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 09:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page