Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help

Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

LinkBack Thread Tools Display Modes
Old 03-08-2002, 07:03 PM
Posts: n/a
560SEL Heater hose replacement completed

I just had one of the heater hoses from the engine block split and cause me to lose all coolant so I took the opportunity to replace all four hoses. These hoses are difficult to remove and refit so it's well worth doing them all at the same time, it makes it easier to get to do the job if you replace them all. I always start at the difficult end first which in this case is the ends in between the two firewalls. The only tools I needed were an 8mm socket, a long handled screw driver, and a sharp knife.

First up remove the rubber strip that sits along the top of the first firewall, this just pulls up and off and then pull the ABS computer up and out of it's holder, this is just an interference fit so pull straight up. Secondly there are three 8mm bolts and a clip that secure the middle section of the first firewall, remove these and the middle section pulls up and slightly towards the front of the car to remove.

With these things out of the way you will now be able to see all the hoses, the two that come from the left and right sides of the engine block through the firewall, and the two that are inside the firewall and run from left to right. The ABS computer bracket is a pain as it prevents easy access to the hose clips, luckily only one couldn't be reached with a screw driver and was relatively easy to get to with a ring and open ender. Once all the hose clips were completely undone and slid off the hoses I used a sharp knife to cut the hose open at the end. Trying to pull these hoses off is very difficult as there is little room and with age they are generally stuck. With the hose cut they slip off much easier. The ends on the engine block couldn't be reached with the knife but there was enough room to simply pull them off. There is a T piece that the hoses connect to in between the firewalls, this needs to be unbolted to get easier access to the hoses.

Replacement is reasonably simply, fit the two engine hoses first and then the others. Ensure that you have the hose clips in the correct way so that you can easily reach them with a long handled screw driver to tighten them. Before refitting the middle firewall section test the cooling system for leaks.

Hope this helps someone, sorry about the lack of pictures but I didn't have access to a camera at the time, and was under some pressure to get this fixed. The hoses were about $50 us all up.

Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
quick heater hose question rhino Diesel Discussion 1 03-03-2004 12:34 PM
1969 280 SL heater controls replacement tadink Vintage Mercedes Forum 1 05-17-2000 08:57 AM
85 300SD Turbo Cooling sys hose replacement Leon Hernandez Tech Help 2 03-29-2000 09:49 PM
Heater Core Replacement (89' 2.6L 190E) Reggie Browning Tech Help 1 01-31-2000 07:29 PM
idle valve bottom hose replacement.... chris Tech Help 1 06-30-1999 08:46 PM

All times are GMT -4. The time now is 05:29 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page