Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help




Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 09-08-2002, 07:50 PM
Registered User
 
Join Date: Jan 2002
Posts: 352
w210 window regulator instructions

My rear driver's side window has dropped down. Seems to me like the window regulator is bust. I took off the door panel (using the diy know how I acquired from you guys) but there is like a pink cover over it. Can anyone give me the instructions on how to fix it. I have a 97 e320. How much is the part, and what parts/tools do I need.
Reply With Quote
  #2  
Old 09-09-2002, 12:21 AM
Registered User
 
Join Date: Apr 2001
Location: Jacksonville Florida
Posts: 723
Post W210 Rear Windoe replacement

Once you have the Rear door panel off you have to peel off the Plastic liner to have access to the window regulator you must drill out the rivets that Secure the Window regulator to the door, Then remove the plastic clip at the Window regulator/door glass then slide the glass/window regulator off and remove the regulator ..Install is the reverse...and install new rivets(Note You Will Need a H.D. pop Rivet gun)And Its about a 30min job...Good Luck

Give the Fast Lane a Call For the Price..The Regulator With Rivets

Last edited by mark cummins; 09-09-2002 at 01:34 AM.
Reply With Quote
  #3  
Old 09-09-2002, 12:26 AM
Registered User
 
Join Date: Sep 2002
Location: los angeles
Posts: 31
i have the same problem with my rear window

I m having a hard time removing the panel. was it difficult to get the door panel off on your car? from this board they mentioned that there should be three big screws to be removed. i have only found two big one and one small one. (one below the arm rest, one behine the black shaped plastic and the small one is from the U shaped plastic near the door latch) Where is the third big screw? thank you in advance for your help.
Reply With Quote
  #4  
Old 09-09-2002, 12:37 AM
Registered User
 
Join Date: Apr 2001
Location: Jacksonville Florida
Posts: 723
There is a screw behind the srs plastic plug,another under the arm rest,another behind the plastic cover for the inside door handle release,The lock pin,and pop it off( The Door Panel) with a plastic wedge...
Reply With Quote
  #5  
Old 09-09-2002, 12:40 AM
Registered User
 
Join Date: Sep 2002
Location: los angeles
Posts: 31
There is no SRS emblem on the rear door panel

my car does not have the SRS emblem on the rear door panel..i see that emblem on the front door though. my car is a 96 E320.
Reply With Quote
  #6  
Old 09-09-2002, 12:55 AM
Registered User
 
Join Date: Apr 2001
Location: Jacksonville Florida
Posts: 723
Sounds like You have them all, Pop The Bottom edge of the door panel out/off and push the door panel up to release the arm rest/handle its secured to the door / Slides into the door...This should do it...
Reply With Quote
  #7  
Old 09-09-2002, 12:58 AM
Registered User
 
Join Date: Sep 2002
Location: los angeles
Posts: 31
thanks Mark, i will try that tomorrow.

thank you very much..
Reply With Quote
  #8  
Old 09-09-2002, 01:49 PM
Registered User
 
Join Date: Jan 2002
Posts: 352
Dont have a rivet gun, so I just took it to the mechanic to fix
Reply With Quote
  #9  
Old 09-09-2002, 04:16 PM
Registered User
 
Join Date: Sep 2002
Location: los angeles
Posts: 31
rivet gun question

sorry for being naive but is there a special rivet gun or any would do? and H.D. means home depot right?
Reply With Quote
  #10  
Old 09-09-2002, 05:40 PM
Registered User
 
Join Date: Apr 2001
Location: Jacksonville Florida
Posts: 723
The Rivets Require a BIG Pop Rivet Gun!Heavy Duty..Not Home depot..You must have the Correct rivet gun!
The one that Comes as a Set Wont work...The Rivets are Big!
Reply With Quote
  #11  
Old 09-09-2002, 05:48 PM
Registered User
 
Join Date: Sep 2002
Location: los angeles
Posts: 31
rivet gun question

Mark, can this gun be purchase at any store you know? and it is very expensive? thank you.
__________________
96 E320
Reply With Quote
  #12  
Old 09-09-2002, 06:10 PM
Registered User
 
Join Date: Apr 2001
Location: Jacksonville Florida
Posts: 723
Any (GOOD) Hardware store should have a Heavy Duty Pop Rivet gun..Have Not seen the gun at The Home Depot
Reply With Quote
  #13  
Old 09-09-2002, 06:55 PM
monkeyseedo
 
Join Date: Aug 2002
Location: ATLANTA, USA
Posts: 15
W210 WINDOW REGULATOR

WHAT IF HE JUST REPLACES THE RIVETS WITH GOOD BOLTS AND NUTS ? [ I HONESTLY WANT TO KNOW THE EFFECT}
Reply With Quote
  #14  
Old 09-12-2002, 05:51 PM
Registered User
 
Join Date: Jan 2002
Posts: 352
UPDATE

$350 to fix. Mech could only buy the regulator w/ motor. Does the E420 have the same probelms with regulators. I am considering dumping the 320 and buying a v8 w210
Reply With Quote
  #15  
Old 09-12-2002, 11:53 PM
Registered User
 
Join Date: Sep 2002
Location: los angeles
Posts: 31
window fixed. Thank you Mark

Your instructions was right on. Once i got the door panel off, everything was just like you described. Thanks again for all your help. This forum is the best.
__________________
96 E320
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 02:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page