Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 11-14-2002, 08:14 PM
Registered User
 
Join Date: Jan 2001
Location: Northern Virginia
Posts: 46
coil problems on '86 W124

Hi guys,

Ok, heres what happened.

1. 1 week ago my car wouldn't start(1986 300E with the M103.983 motor)

2. Diagnosed the problem to a bum coil. Used a timing light to find a no spark condition on all plugs.

3. Absolutley needed the part ASAP. Local dealer quoted $177 and would have to order, would take 3-4 days.

4. Local Euro Import shop had the correct Bosch coil in stock, price $66 bucks. Just to be sure I take the old coil to the shop, we compare part numbers, find out that Bosch has a "superceded" or updated part, and the one he has in stock is this new part.

5. Take it home, it installs perfectly, all the bolt holes line up, the terminals are in the right place and the right size etc.

6. Car starts and runs GREAT.......for exactly one week


7. Now same conditions found, no spark on any plugs using timing light method.


Does anybody have any ideas?? Could something( and what thing) could be burning out coils? or could it just be a bad/wrong coil.(perhaps this coil wasn't quite up to MB standards) even though that seems hard to beleive since the original coil was Bosch manufacture.


Sure would appreciate some insight from you guys.


Thanks
Evan

Reply With Quote
  #2  
Old 11-14-2002, 08:53 PM
it leaks, its german
 
Join Date: Mar 2002
Location: raleigh nc
Posts: 1,111
Ok, first off a coil has to have power and ground interuption (signal) to fire. However, the flaw in your testing is simple, you check for fire from the coild at the coil wire, you check the spark plugs wires for cap and/or rotor problems. Take the coil wire off, place the end about 1/4" from metal and have someone turn the motor over for you, if it fires, it aint the coil. :-) If it does not fire, time to look for signal, this can be done with a dvom or a test light by removing the ground lead and chacking for ground interuption.

If you have fire from the coil and none to the plugs either you have a bad cap, rotor or rotor support. If you have no signal for fire to the coil, EZL or crank sensor. However, before you condem anything, make sure you cover the basics, power to the coild, fuses ok, OVP (while it wont stop a 103 from starting it will cause other weird problems.)


Joe
__________________
Project Smoker, '87 603 powered wagon
Hauler, 96 CTD can you say torque?
Toy 73 Cougar xr7 convertible
Acme Automotive Inc.
Raleigh NC
919-881-0364
Reply With Quote
  #3  
Old 11-14-2002, 08:54 PM
it leaks, its german
 
Join Date: Mar 2002
Location: raleigh nc
Posts: 1,111
Oh ....DOHHHHHH!

New parts crap out too. :-)


Joe
__________________
Project Smoker, '87 603 powered wagon
Hauler, 96 CTD can you say torque?
Toy 73 Cougar xr7 convertible
Acme Automotive Inc.
Raleigh NC
919-881-0364
Reply With Quote
  #4  
Old 11-15-2002, 01:07 PM
Registered User
 
Join Date: Jan 2001
Location: Northern Virginia
Posts: 46
joe,, again tell me how do I check to see if the coil is getting signal? I understand that the crank position sensor feeds in to the ezl, and then it into the coil. I'm pretty sure that theres no juice coming out of the coil wire going to the rotor, since I clamped and inductive timing light around the coil lead, and cranked the motor: no light, I figure it should have lit up continuosly. To check for signal, how do you do that... I'm assuming it one(or both) of the small (small bolt and nut) arrangement on the top of the coil. I see that one side appears to be grounded,,,,,,can you use a test light or DMM to check for voltage across those points????


Thanks
Evan
Reply With Quote
  #5  
Old 11-15-2002, 05:21 PM
dpetryk's Avatar
Electrons can do anything
 
Join Date: Sep 2001
Location: Houston, Texas
Posts: 1,072
The EZL ignition module may have a problem. If you have a scope check for signal across the the two terminals of the coil. Not the HV (secondary winding) but the primary windings connections. A voltmeter could also be used.

__________________
I got too many cars!! Insurance eats me alive. Dave

78 Corvette Stingray - 3k
82 242 Turbo Volvo - Manual - 270k
86 300e 5 speed manual - 210k
87 420sel - 240k
89 560sl - 78k
91 420sel - 205k
91 560sel - 85k
94 GMC Suburban - 90k
97 Harley Davidson Heritage Softail - 25k
00 GMC Silverado 1 ton 30k
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 08:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page