Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 02-15-2003, 09:50 PM
Registered User
 
Join Date: Nov 2002
Location: Los Osos, CA
Posts: 212
Unhappy Oil Drain Plug stripped NEED HELP QUICK

This is most definately not good. Started to do an oil change on my 300e today and found that the oil drain plug came out very easily. Didn't think anything of it until I started to put it back in. It threaded in and tightened to around 8ft pounds and then got loose again. Another full turn yielded the same result. My manual says to tighten it to 18ft pounds. I'm pretty sure the oil pan threads are stripped and am not certain if the car should be driven. Filled it with oil and let it idle for 5 minutes, no leak or spray, but when I put my finger on the plug I found new oil on my finger. What do I do? Is it hard to replace an oil pan? Could the pan be tapped and a new plug inserted without taking the pan off? I would greatly appreciate any help you can offer.

Scott

Reply With Quote
  #2  
Old 02-15-2003, 10:01 PM
chicago124
Guest
 
Posts: n/a
Hi,

Do a search on oil drain plug. I found an answer about that subject.

I now use a Stearns electrical pump to get the oil out through the dipstick. Easy and less cleanup.

Will probably change the oil more often this way -- every two thousand miles or so.

Anyway, there is a solution in the archives and it involves a tap and die set.

Good luck,

chicago124
Reply With Quote
  #3  
Old 02-15-2003, 10:12 PM
jbaj007's Avatar
Registered User
 
Join Date: Jun 2001
Location: Santa Monica, CA
Posts: 2,053
Peruse this.. http://www.cgenterprises.com/drain_plugs.htm

Everything you hoped you would never need to know.

DOS means double oversize
SOS means single
TOS you take it from here
__________________
The Golden Rule

1984 300SD (bought new, sold it in 1988, bought it back 13 yrs. later)

Last edited by jbaj007; 02-15-2003 at 10:31 PM.
Reply With Quote
  #4  
Old 02-16-2003, 12:14 AM
Registered User
 
Join Date: Nov 2002
Location: Los Osos, CA
Posts: 212
Alright, talked my girlfriend's dad, who does engine machining. He said that we could use loctite to just seal the plug in the car. So the new plan, and the one that will save me $500 to retap the plug is to either loctite in the original bolt and use a topsider device or loctite in a plug with a valve in it. Any problems with these ideas?
Reply With Quote
  #5  
Old 02-16-2003, 12:49 AM
Registered User
 
Join Date: Jul 2002
Location: Dallas
Posts: 330
You might try a new plug. Maybe it is what is stripped out, rather than the pan. A new oil pan is $231: A new plug costs $1.28 at performancemotorcars.com. $500 to retap is ridiculous though. Take it to a full service filling station and they'll probably do it for $30.

Use some teflon tape on the drain plug until you get it fixed.

Anybody else see anything wrong with these suggestions?

Last edited by 95E320cab; 02-16-2003 at 12:58 AM.
Reply With Quote
  #6  
Old 02-16-2003, 12:59 AM
Registered User
 
Join Date: Jan 2002
Location: NY
Posts: 500
I wouldn't trust locktite in this aplication for anything but temporary repair. You risking too much! I think the original drain plug is M12x1.5. You can try to tap standard 1/2 inch thread there. (1/2" = 12.7 mm).

Last edited by myarmar; 02-16-2003 at 10:48 AM.
Reply With Quote
  #7  
Old 02-16-2003, 08:37 AM
aTOMic's Avatar
(Oo=*=oO)
 
Join Date: Aug 2001
Location: Hendersonville, Tennessee, USA, Earth
Posts: 451
I got a replacement plug from AutoZone last night, $1.69 it was M12 X 1.5 and has a magnet to catch metal flotsam.
Permatex (Loctite) makes a thread restorer product that is an epoxy to create new threads, I think Permatex could make this work if anyone could. You could use this with a drain valve to reduce the possibility of stripping it in future oil changes.

Good luck!
-Tom
__________________
RIP "Betsy" (Oo=*=oO)
'96 E 3 2 0 (W 2 1 0) M 1 0 4
(Totalled)

Spaces in sig so as not to screw up the SEARCH; every time someone searches for that MB they don't want my sig!

2004 Audi A8L
'98 VW Passat 1.8T 5M
'87 Alfa Romeo Milano 2.5L 5M
'67 Impala convertible, 327cid
Reply With Quote
  #8  
Old 02-16-2003, 12:14 PM
Registered Diesel Burner
 
Join Date: Aug 2001
Location: Northern Virginia
Posts: 2,911
I can't see what your drain plug looks like, but my general advice would be to make the minor investment in a new drain plug when you go with the "sealer" route - and topsider in the future.

There's lots of things you can try. Loctite is pretty good for a solution that you can back out of later. The Permatex product that aTOMic mentioned sounds good. Teflon tape might work too - all good suggestions.

If you want a seal that will never leak, but would be pretty difficult to back out of - use JB Weld epoxy.

The problem a lot of people get into with these drain plugs is rounding off the fairly soft head, rather than stripping the threads. So, I'd have to recommend to everyone - use a 6-pt socket, and follow the torque recommendation carefully.

Ken300D
Reply With Quote
  #9  
Old 02-16-2003, 04:41 PM
Registered User
 
Join Date: Nov 2002
Location: Los Osos, CA
Posts: 212
Talking

Hehe, found a valve to replace the drain plug at www.fumotovalve.com. I will look into Ken's JB weld epoxy. These valves are supposed to last for pretty much the life of your engine. I plan to just glue the sucker in there as permanently as is possible.
Reply With Quote
  #10  
Old 02-16-2003, 04:42 PM
Registered User
 
Join Date: Nov 2002
Location: Los Osos, CA
Posts: 212
Here is a pic of the valve, looks a bit more substantial than the ones they are selling at autozone.
Attached Thumbnails
Oil Drain Plug stripped NEED HELP QUICK-valve2.jpeg  
Reply With Quote
  #11  
Old 02-16-2003, 05:40 PM
Registered User
 
Join Date: Feb 2003
Location: riverside ca.
Posts: 6
oil drain bolt stripped

at your local parts store the sell a kit to repair the stripped hole. it is a two piece set. first piece screws into your stripped hole, it has a hole in it also, and the other piece goes into threads in to the first one giving you a new drain bolt.
knukelbuster
30 years a fleet mechanic
Reply With Quote
  #12  
Old 02-18-2003, 04:05 PM
Joseph_H's Avatar
Registered User
 
Join Date: Nov 2002
Location: Texas
Posts: 231
If all fails, replace oil pan

I replaced my oil pan for $82 and took me 1/2 hour to do it on my E420. it was easy to get to all bolts. Add $10 for new gasket. otherwise, all suggestions above seem to make sense as well.
__________________
Joe95E420
Reply With Quote
  #13  
Old 02-18-2003, 05:45 PM
Registered User
 
Join Date: Nov 2002
Location: Los Osos, CA
Posts: 212
I was quoted 6 hours labor to remove the pan for the M103 6cyl. $450 in all, 400 labor and 50 for tapping the plug.

Got the JB Weld and the oil drain valve is being overnighted, needed also an adapter for the 300e drain valve. I will have it fixed by tomorrow evening.
Reply With Quote
  #14  
Old 02-18-2003, 06:38 PM
Registered User
 
Join Date: Jan 2002
Location: NY
Posts: 500
Why one needs to remove the oil pan to do it? I'm not familiar with your car, but I can't beleive it can't be done without oil pan removal.
Quote:
Originally posted by 6cndmbz
I was quoted 6 hours labor to remove the pan for the M103 6cyl. $450 in all, 400 labor and 50 for tapping the plug.

Got the JB Weld and the oil drain valve is being overnighted, needed also an adapter for the 300e drain valve. I will have it fixed by tomorrow evening.
Reply With Quote
  #15  
Old 02-18-2003, 09:03 PM
Registered User
 
Join Date: Nov 2002
Location: Los Osos, CA
Posts: 212
The shop said they thought it a better idea to remove the pan, as shavings from tapping the plug hole might get into the oil otherwise . It doesn't matter though, because by inserting the drain instead, I don't have to worry about shavings and most definately don't have to remove the pan.

Scott

Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 08:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page