Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help

Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

LinkBack Thread Tools Display Modes
Old 05-11-2000, 03:26 AM
Posts: n/a
I've decided to replace my camshafts and rockers myself. My mechanic checked the oil when he heard a knock and found only a quart left. I had him do diagnostics and sure enough, the cam tips are scored. Not pretty. The compression was fine which leads me to believe that the rings were fine.

The last oil change was in December (I'm horrible!) so I'm averaging my oil loss at a little more than a quart a month. If this consumption is average for the age, the rings are fine, and there are no oil leaks, what else could cause the loss?

I'm afraid that I need to do a valve job as well. If I don't need to pull off the cylinder head, I'm comfortable doing the cam work myslef. The engine has 190k miles on it and the camshafts were replaced at 140k.

Anything else I should look at while I'm getting dirty? Any do's or do not's?


- Matt

Reply With Quote
Old 05-11-2000, 09:22 AM
Join Date: Mar 2000
Location: Gainesville FL
Posts: 6,844
If I was going to do this I would replace the valve guide oil seals first. This is undoubtably the source of your oil consumption.

I would hold off replacing the cams till this is verified. The reason for this is that the cam stand bolts (half of them) are also head bolts. On the aluminum block motors you stand a risk of taking the threads out either when you remove the bolts or with the retorque. If the bolt won't tighten, the head must come off. So you should find out if the valve guides are resealable first as doing a valve job will cause all this to come apart anyway.

With 191k your valve guides are about worn to the limits and same goes for the chain and upper rails (if original). I would do the whole job at once or at least be prepared to if you can't retorque the bolts.

The two bolts that hold each stand are allen bolts. There are many techniques to remove such bolts and you may not need any but be carefull with your technique. My best tech has to drill the head off one bolt out of 100 even knowing all the tricks. The problem comes from wallowing out the allen hole. If I (personally) did a valve job on a motor that old I would stand a 50/50 chance of ruining at least one bolt (even knowing to be carefull - I do not have his touch or experience - I have seen him work a bolt for a half hour to avoid rounding - to avoid hour(s) of work if he fails)

Probably the best technique as last resort (ruins the bolt) is to have one tech hold a heavy torque on the bolt (considerably more than normal break-away torque) while another tech hits the head in the direction of release with an air impact chisel. The key to this last resort is doing it before you strip the allen hole as you have to be able to exert at least over torque; the impact chisel alone won't get it.

Steve Brotherton
Owner 24 bay BSC
Bosch Master, ASE master L1
26 years MB technician

Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
450 SEL and 380 SE Need New Homes jim16671836 Mercedes-Benz Cars For Sale 0 06-23-2003 10:47 PM
83 380 SEL Brake problems, Help acha3 Tech Help 5 10-29-2002 09:22 PM
Hard starting 82 380 SEL Burgenlander Tech Help 2 08-26-2002 09:04 PM
380 SEL shaking and choking BenzOnline Off-Topic Discussion 8 05-31-2002 11:14 PM
Looking at '83 380 SEL W/ 276k on it--any known problems or opinions? zachv Tech Help 1 10-02-2001 05:51 PM

All times are GMT -4. The time now is 04:50 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page