|
|
|
#1
|
|||
|
|||
I have a 230 gas from 1975. I set the dwell to 48 where the shop manual said to set it. Now when I first start up it back fires a little bit out the carb. I believe there was water in the tank so I used a gas treatment. Would a bad fuel filter cause this. Once I give it some gas and it back fires a few times it runs good.
Thanks for your help in advance. |
#2
|
|||
|
|||
I read your other post and almost jumped the gun with an answer. Then I reread it and saw that you had checked the timing. My first jump the gun answer was you were changing the timing with your two dwells. BUT, it was the wrong direction. The lower dwell would result in higher timing (more advanced), which should make it run better.
When I realized that I didn't reply. The M115 Stromberg carbed 4 cyl is very picky about timing. Be sure you are at least at factory setting or above. (I would recommend 5 degrees over factory settings). By factory settings I also mean proper operation of both vacuum advance/retard and centrifical advances. Based upon the back fire issue I would say you are either retarded (or deficient in secondary ignition capabilities/coil/rotor/etc.) or lean. On the Stromberg the choke was a constant problem and the oil resevoir needs to be full of oil. The main diaphram (easily removable by removing the top (three screws if I remeber correctly)should be checked before adjustments are made. ------------------ Steve Brotherton Owner 24 bay BSC Bosch Master, ASE master L1 26 years MB technician [This message has been edited by stevebfl (edited 05-14-2000).] |
#3
|
|||
|
|||
As stated, the higher dwell reading is a closing of the point gap which advances the
timing. You will notice a felt oil res. on the dist. shaft when you remove the rotor. These sometimes never get oiled as they are hidden and the results is wear and slop on the shaft. This shaft is the lobe and advance plate and wear affects the dwell and timing to the point where the points are too close and can cause your backfire. Look for drifting dwell and erratic timing with a light on the timing marks. i have had excellent results with point conversion kits for these older ignition systems. Mechanical switching has many wear drawbacks and is easily replaced with improved performing electronic ign. for short $$$. Arthur |
#4
|
|||
|
|||
Thanks so much with the info you provided. Do you know where I can purchase a conversion set? The problem goes away after a couple minutes can this lead me a certain direction in trouble shooting?
Regards, Chris Patko. quote: |
#5
|
|||
|
|||
Crane has an optical one I like at www.cranecams.com
Check the XR-700 series. Fine for the street. No need to change the coil. Petronics [sp??] has a hall effect one . Simpler , but not as good at cranking speeds [starting]. It is preference and both types are a major improvement over mechanical switching points. Both under $100. Arthur |
#6
|
|||
|
|||
Arthur, Thanks for the help I put a conversion kit in. It runs better but did not fix the problem. It still backfires out the carb when I first start the car. Once driving everything is fine. Any other ideas on nwhat it may be?
quote: |
#7
|
||||
|
||||
I thought that if your timing was too far advanced, you would backfire, especially upon accelleration. But, the backfiring goes away once warm...at least with the old ign. it did. Is there anykind of thermostatic device (like the kind that initiates the preheating of intake air by passing it over the exhaust manifold) that could have a vacuum leak--but only when cold?
my 2¢ -Larry ------------------ 03/83 300D 184k 07/73 280 160k |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Calling all Benz Technician's | ozzy | Tech Help | 7 | 01-25-2005 04:57 AM |
Are MB Technicians Paid Enough? | SHYNE | General Information | 46 | 11-04-2004 02:25 PM |
M.B. Technicians...Can you help me? | ckroeger | Tech Help | 1 | 02-04-2003 05:07 PM |
Technicians, what kind of lifestyle are you living? | SHYNE | Off-Topic Discussion | 17 | 12-23-2002 12:10 PM |
2.6 stroker 16v owners and technicians! | 190evol1 | Mercedes-Benz Performance Paddock | 14 | 09-09-2002 12:23 AM |