|
|
|
#1
|
|||
|
|||
Rebuilding heater control valves on W108
Well, I finally got around to the heater controls on the 280. Need to replace the right red one (lever broken off, naturally).
I finally found the valves, assuming they were stuck took a pair of plier to them and got them working, but now (actually, before I moved them) at least one leaks. I've been told there is a kit to repair these, has anyone done this? Anything I need to do (other than lots of penetrating oil on those rusty screws!)? I don't see the kit in FastLane, but was told it is a pair of o-rings for each valve. I'm going to be draining the coolant anyway (stupidly didn't replace the thermostat when I did the water pump), so thought I just dive in and fix the valve at the same time. It's going to get cold enough soon that I will want some heat. Thanks in advance! Peter
__________________
1972 220D ?? miles 1988 300E 200,012 1987 300D Turbo killed 9/25/07, 275,000 miles 1985 Volvo 740 GLE Turobodiesel 218,000 1972 280 SE 4.5 165, 000 - It runs! |
#2
|
|||
|
|||
psfred,
My Catalog "B" shows the two o-rings, one just above the water outlet and another smaller 0-ring just below the outlet, or a total of four o-rings for the split heating system. Top o-ring makes sense (seals top plate), bottom o-ring doesn't (I wouldn't use an o-ring for a shaft packing seal but I guess you never know). Catalog also shows a strange clip like thing just to left of control valve's left fire wall mounting hole. Haven't had one apart and catalog doesn't show exploded view but I can't imagine anything more complicated than two butterfly valves in a common housing. Give us the run down when you get it fixed.
__________________
daBenz - 1970 220D |
#3
|
|||
|
|||
Peter,
After you remove the circlip, you slide the valve out noting position and replace the two O rings. I would suggest the dealer or Miller's in Southern Cal as sources. Hopefully you can get them out without destroying them since they are made of brass. MB made a special for the job. I used to have one. The colored levers can be bought as original equip or a company that advertises in the STAR sells screw on units that require no disassembly. I installed a set years ago, and they worked quite well.Remember to install those valves so they rotate full open and full closed. Peter
__________________
Auto Zentral Ltd. |
#4
|
|||
|
|||
Thanks guys!
This may wait until the weekend, I'm too old to crawl around in the car with a flashlight at night to fix anything anymore! Peter
__________________
1972 220D ?? miles 1988 300E 200,012 1987 300D Turbo killed 9/25/07, 275,000 miles 1985 Volvo 740 GLE Turobodiesel 218,000 1972 280 SE 4.5 165, 000 - It runs! |
#5
|
|||
|
|||
The consensus on the mercedes-veterans list when this came up was to remove the valve and take it to Home Despot or a good HW store to buy o-rings that fit.
__________________
Chuck Taylor Falls Church VA '66 200, '66 230SL, '96 SL500. Sold: '81 380SL, '86 300E, '72 250C, '95 C220, 3 '84 280SL's '90 420SEL, '72 280SE, '73 280C, '78 280SE, '70 280SL, '77 450SL, '85 380SL, '87 560SL, '85 380SL, '72 350SL, '96 S500 Coupe |
#6
|
|||
|
|||
Peter,
According to my microfiche, the part #s for the 2 seals are: 000-835-12-98 and 000-835-13-98. You need 2 of each per car. I still have a few of each, but I will need them when I have problems with my 230SL,280SL, or 3.5 coupe. They should be available from MB. Peter
__________________
Auto Zentral Ltd. |
Bookmarks |
|
|