Porsche
/
BMW
/
Mercedes
/
Audi
/
Volkswagen
/
Saab
/
Volvo
/
MINI
All
Search Everything
Cart
|
Project List
|
Order Status
|
Help
Shop by Brand
/
Shop by Category
PeachParts Mercedes-Benz Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
ShopForum Gallery
FAQ
Calendar
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Advanced Search
Go to Page...
Page 1 of 17
1
2
3
11
>
Last
»
Showing results 1 to 30 of 500
Search took
0.12
seconds.
Search:
Posts Made By:
JimSmith
Forum:
Diesel Discussion
10-04-2022, 09:04 PM
Replies:
13
My 240D, new issue....
Views:
1,136
Posted By
JimSmith
Sounds like glow plugs should be OK, and fuel...
Sounds like glow plugs should be OK, and fuel quality is likely OK from the tank. However, it may be that your injectors are not all "equal" and one may be either a bit dirty or otherwise not moving...
Forum:
Diesel Discussion
08-10-2022, 07:57 PM
Replies:
16
Power steering
Views:
1,233
Posted By
JimSmith
That's what I do. I suck the stuff out of the...
That's what I do. I suck the stuff out of the reservoir with a turkey basting or similar device, remove the filter and try to wipe the reservoir clean, then disconnect the return hose and aim it...
Forum:
Diesel Discussion
08-10-2022, 07:26 PM
Replies:
23
Uneven brake disk/pad wear W123
Views:
1,476
Posted By
JimSmith
I usually have to abuse an old Craftsman long...
I usually have to abuse an old Craftsman long handled screw driver to chisel the junk -combination of rust and corroding metallic (disc and pad) residue bonding to the guide surfaces of the caliper. ...
Forum:
Mercedes-Benz Cars For Sale
08-16-2015, 12:56 PM
Replies:
2
1984 W123 Gas Engine 230E For Sale
Views:
931
Posted By
JimSmith
I am also looking to sell my 1983 240D in my...
I am also looking to sell my 1983 240D in my signature. It has been sitting for too long and the floor flooded the last few years because the rear window seal has failed. I have been living in...
Forum:
Mercedes-Benz Cars For Sale
08-16-2015, 12:50 PM
Replies:
2
1984 W123 Gas Engine 230E For Sale
Views:
931
Posted By
JimSmith
I know a dash from 1984 with no cracks sounds...
I know a dash from 1984 with no cracks sounds outrageous so here are some photos :
Jim
No idea why these photos came out upside down....
Forum:
Mercedes-Benz Cars For Sale
08-16-2015, 12:45 PM
Replies:
2
1984 W123 Gas Engine 230E For Sale
Views:
931
Posted By
JimSmith
1984 W123 Gas Engine 230E For Sale
This car belonged to my Aunt who had it looked after by a local independent shop in the Fort Lee area of NJ since it was new. I imported it, along with several other vehicles at that time, and had...
Forum:
ML, GL, G-Wagen, R-Class, Unimog, Sprinter
03-04-2015, 11:21 PM
Replies:
2
2009 ML320 BlueTec - Drive Line Vibration
Views:
1,374
Posted By
JimSmith
2009 ML320 BlueTec - Drive Line Vibration
I purchased a 2009 ML320 BlueTec 5 years ago with ~10,000 miles on it, and have driven the vehicle an additional 125,000 miles now. I have had 3 items fail that were not warranty items, an AddBlue...
Forum:
Diesel Discussion
04-28-2014, 01:55 AM
Replies:
12
6-speed from an SLK in an E300?
Views:
3,203
Posted By
JimSmith
I will be following this thread to see how it...
I will be following this thread to see how it goes. My son just bought a G300D from 1980 with a manual (non-turbo). He wants to put a 606 engine in it but wants to keep it a manual. Have to see...
Forum:
Diesel Discussion
10-14-2013, 10:17 PM
Replies:
6
Anyone Have A Source for a 1998 W210 Blower Motor?
Views:
841
Posted By
JimSmith
Thanks guys. I ordered a rebuilt motor from...
Thanks guys. I ordered a rebuilt motor from George Murphy after a few minutes of talking to him. Good guy. The part number is, by the way, 0 130 111 043. This series of motor fits a bunch of cars...
Forum:
Diesel Discussion
10-14-2013, 02:32 PM
Replies:
6
Anyone Have A Source for a 1998 W210 Blower Motor?
Views:
841
Posted By
JimSmith
Thanks, the guy was great on the phone, has...
Thanks, the guy was great on the phone, has brushes and motors for everything MB it seems. Great source, thanks again.
Jim
Forum:
Diesel Discussion
10-14-2013, 02:04 PM
Replies:
6
Anyone Have A Source for a 1998 W210 Blower Motor?
Views:
841
Posted By
JimSmith
Thanks, it looks like the motor itself is in...
Thanks, it looks like the motor itself is in short or no supply, so I will remove the brushes tonight, measure them up and order new ones. Thanks,
Jim
Forum:
Mercedes-Benz Cars For Sale
10-13-2013, 09:38 PM
Replies:
14
If I don't sell this week, they are getting crushed.
Views:
2,387
Posted By
JimSmith
What is the structural and cosmetic condition of...
What is the structural and cosmetic condition of the W123? I have a strong 240D engine and transmission in a near terminally rusted body. I have a big decision to make on that one too....and where...
Forum:
Diesel Discussion
10-13-2013, 06:27 PM
Replies:
6
Anyone Have A Source for a 1998 W210 Blower Motor?
Views:
841
Posted By
JimSmith
Anyone Have A Source for a 1998 W210 Blower Motor?
Fixed my speed control unit last summer, using the W140 replacement unit as described herein in another post and now, a year later the motor burned up. It is likely brushes and I would also just go...
Forum:
Diesel Discussion
10-13-2013, 06:20 PM
Replies:
87
606 go Kaboom.
Views:
6,647
Posted By
JimSmith
Sorry to hear that. Mine is reaching the 240,000...
Sorry to hear that. Mine is reaching the 240,000 mile mark and the engine runs like a top still. No change in oil consumption for 200,000 miles. Have it in Colorado now and I routinely get over 35...
Forum:
Diesel Discussion
08-31-2013, 11:47 PM
Replies:
16
OM606 stalling after brakes applied
Views:
4,467
Posted By
JimSmith
I finally got around to removing the driver's...
I finally got around to removing the driver's side tail light assembly and figuring this problem out. The blinker lamp is inserted in a plastic socket with electrical contacts that became, over time,...
Forum:
Diesel Discussion
03-27-2013, 01:16 AM
Replies:
56
300d 4-speed swap: are you happy with it?
Views:
14,346
Posted By
JimSmith
Congratulations! Sounds like a hell of a lot of...
Congratulations! Sounds like a hell of a lot of work with exceptional results! Makes one wonder why MB elected not to make the drivetrain available then, and today. Thanks for posting the...
Forum:
Diesel Discussion
03-23-2013, 01:46 PM
Replies:
18
Weird grinding sound from back left wheel
Views:
2,288
Posted By
JimSmith
The arrangement of the hardware in the rear wheel...
The arrangement of the hardware in the rear wheel well of a W123 is quite simple and once the rear wheel is removed, quite accessible. I do not believe spraying some WD40 or the like "around" back...
Forum:
Diesel Discussion
03-16-2013, 05:05 AM
Replies:
13
update on my 1999 e300
Views:
1,309
Posted By
JimSmith
Great cars, mine gets 29 mpg at sea level. At...
Great cars, mine gets 29 mpg at sea level. At nearly 6,000 ft it gets 35. Turbo makes altitude effect on performance next to nil, but without the air density the low drag body combines to give...
Forum:
Diesel Discussion
03-15-2013, 01:51 AM
Replies:
262
Little or NO power after bottoming out suspension- 1981 300SD
Views:
19,985
Posted By
JimSmith
Not having done this job on a 617 I may very well...
Not having done this job on a 617 I may very well be wrong regarding doing this job, but, I have done it on a 16 valve 190 and it wasn't that big a deal. The 190 had the same oil pressure behavior...
Forum:
Diesel Discussion
03-15-2013, 12:20 AM
Replies:
262
Little or NO power after bottoming out suspension- 1981 300SD
Views:
19,985
Posted By
JimSmith
The lack of oil pressure is a new and potentially...
The lack of oil pressure is a new and potentially significant piece of information. When the bearings are starved for oil, the rate of wear increases and clearances grow. When the clearances grow...
Forum:
Diesel Discussion
03-12-2013, 10:56 AM
Replies:
262
Little or NO power after bottoming out suspension- 1981 300SD
Views:
19,985
Posted By
JimSmith
I think the question is aimed at finding out if...
I think the question is aimed at finding out if the starter motor turned the crankshaft when the attempt to start the engine immediately after it shut off following the bottoming out event. The...
Forum:
Diesel Discussion
03-11-2013, 11:29 PM
Replies:
262
Little or NO power after bottoming out suspension- 1981 300SD
Views:
19,985
Posted By
JimSmith
And any single or combination of belt driven...
And any single or combination of belt driven loads that approaches 35hp at ~2000 rpm is going to make the source of the load glow in the dark in short order. That is a lot of heat for an alternator...
Forum:
Diesel Discussion
03-11-2013, 10:19 AM
Replies:
262
Little or NO power after bottoming out suspension- 1981 300SD
Views:
19,985
Posted By
JimSmith
I am unable to comment on the event that caused...
I am unable to comment on the event that caused the problem which may well have involved oil starvation and been the reason the machine shut down. Since then the engine has been operated for...
Forum:
Diesel Discussion
03-10-2013, 08:05 PM
Replies:
855
wont start for anything! 1985 300SD
Views:
140,102
Posted By
JimSmith
I remember this thread well, and am sad to hear...
I remember this thread well, and am sad to hear Sady has been overcome by the forces of Mother Nature. Great story, and the essence of what makes a great web site.
Jim
Forum:
Diesel Discussion
03-10-2013, 06:24 PM
Replies:
262
Little or NO power after bottoming out suspension- 1981 300SD
Views:
19,985
Posted By
JimSmith
Brian, I am intrigued. Wouldn't full...
Brian,
I am intrigued. Wouldn't full throttle fuel flow with an improper injection timing setting just make more smoke?
Does this engine, like the 240D, have any intake side or other...
Forum:
Diesel Discussion
03-10-2013, 06:15 PM
Replies:
262
Little or NO power after bottoming out suspension- 1981 300SD
Views:
19,985
Posted By
JimSmith
Interesting thread. Quite frustrating to get...
Interesting thread. Quite frustrating to get through the 160 some odd posts and finding no solution.
I hate to be argumentative, but to run an engine that is consuming more than 35hp in...
Forum:
Diesel Discussion
03-10-2013, 12:56 AM
Replies:
16
OM606 stalling after brakes applied
Views:
4,467
Posted By
JimSmith
The throttle is operated electronically on this...
The throttle is operated electronically on this auto. So, there is no mechanical connection between the pedal and the injection pump.
There are a couple of sensors that have to be "seeing" a...
Forum:
Diesel Discussion
03-09-2013, 11:55 PM
Replies:
16
OM606 stalling after brakes applied
Views:
4,467
Posted By
JimSmith
I have a primitive code reading tool and have...
I have a primitive code reading tool and have checked, with no codes detected. I presume the brake light circuit is part of the trigger to drive the engine to idle, and my car's issues with the tail...
Forum:
Diesel Discussion
03-09-2013, 02:10 PM
Replies:
4
Thread pitch of Alternator Mounting Bolt
Views:
1,165
Posted By
JimSmith
I would buy two bolts, one each of the two...
I would buy two bolts, one each of the two available thread pitch versions available, and see which threads into the female end. I would be kind of surprised if the fine pitch is uses as this is not...
Forum:
Diesel Discussion
03-09-2013, 02:03 PM
Replies:
49
Injector heat shields are stuck, Help!
Views:
3,584
Posted By
JimSmith
Sears used to sell a screw driver tool with a...
Sears used to sell a screw driver tool with a tapered thread on the business end and probably still do. I use that to get a grip on the shield and then like others, rock it back and forth and kind...
Showing results 1 to 30 of 500
Page 1 of 17
1
2
3
11
>
Last
»
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Mercedes-Benz Tech Information and Support
Tech Help
Diesel Discussion
Diesel Performance Tuning
Alternative Fuels
Vintage Mercedes Forum
Mercedes-Benz SL Discussion Forum
ML, GL, G-Wagen, R-Class, Unimog, Sprinter
Mercedes-Benz Performance Paddock
Mercedes-Benz Wheels & Tires
Car Audio and Multimedia
Detailing and Interior
Mercedes-Benz Classified Ads
Mercedes-Benz Cars For Sale
Mercedes-Benz Used Parts For Sale & Wanted
Pelican Parts Promos, Special Offers & New Products
Pelican Parts Mercedes-Benz Catalog
Do It Yourself Links & Resources
Restoration Projects & Long-Term Builds
Bodywork - Repair, Paint, Tools, Tips & Tricks
Mercedes Parts Reference Library
DIY Links by Parts Category
General Information
Tool Rental Program
Regional Forums
Southeast - US (AR,AL,FL,GA,KY,LA,MS,NC,SC,TN)
Pacific NorthWest -US (WA/ID/OR/UT/HI/AK)
Great Lakes - US (IL,IN,MI,MN,OH,WI)
Northeast - US (NY/NJ/CT/MA/ME/NH/RI/VT)
California / SouthWest - US (AZ/NV)
Middle Atlantic - US (DC,DE,MD,PA,VA,WV)
Tex-Mex (TX, OK, NM, Mexico)
Great Plains & Rocky Mountains - US (CO,IA,KS,MO,MT,ND,NE,SD,WY)
Video Forum
Featured Cars
Good MB Shops
Canada
International & Other
Events & Gatherings
General Discussions
Off-Topic Discussion
Site Feedback
All times are GMT -4. The time now is
01:33 AM
.
-- Normal ShopForum Style
---- Copy of Normal ShopForum Style
-- Pelican_Mobile
Contact Us
-
Mercedes-Benz Discussion Forum
-
Archive
-
Privacy Statement
-
Terms of Service
-
Top
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by
vBSEO
3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -
DMCA Registered Agent Contact Page