Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help

Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

LinkBack Thread Tools Display Modes
Old 10-06-2003, 11:17 AM
Registered User
Join Date: Jan 2001
Location: Northern Virginia
Posts: 46
Need pin numbers and codes for ASR

HI guys,

I just completed building my "test light" for my '95 E320 wagon. Thanks for the schematics. I now need to know what pins on the socket to connect to, and the codes for and ASR trouble light that is on in my '95 E320 wagon. The lights been on for about a week, no noticeable changes in the way the car runs at all, just the light comes on after the car is running for about 10 min.

Evan Lewis

Reply With Quote
Old 10-06-2003, 01:52 PM
Posts: n/a
you need to hook your newly made scan tool to socket 14 and read the codes. Let us know what you get. Socket 14 is the EA/CC/ISC socket for ASR and non-ASR vehicles.
Reply With Quote
Old 10-12-2003, 06:34 PM
Registered User
Join Date: Jan 2001
Location: Northern Virginia
Posts: 46
codes from socket 14


these are the codes that I extracted from pin14 on my '95 E320

PIN14 returned:

6,11 and 14

I checked out the other pins as well and the only other one that returned codes was PIN3

4.6 and 9

I appreciate all your help..

BTW. since the radio shack guy told me that the led he had on hand had 1k of resistance built in...I did not put another resistor in the system( the codes on pin 3 co-incicded with the codes returned by the little push I figured it's working correctly)

Reply With Quote
Old 10-13-2003, 10:13 AM
Posts: n/a
ok Evan, your code reader is built correctly by not using a 1k ohm resistor, it's usually built into the LEDS.

Now for some discouraging news, I would clear the codes and hold your breath for a while to see if your ASR light goes out and those codes return. Reason is they are the same codes I had when I discovered the wiring harness was shot on my throttle actuator. There seems to be a few people besides myself lately that have had to replace them and they're not cheap.

Socket 14 codes: EA/CC/ISC

Code 6 - Starter lock-out/back-up lamp switch
Code 11 - Fuel Safety Shut-off Signal
Code 14 - CTP switch
Reply With Quote
Old 10-13-2003, 12:09 PM
JimF's Avatar
'94 S500: only 793 sold!
Join Date: Mar 2001
Location: San Diego, CA
Posts: 1,933
Here's the DTCs for . . .

Pin 3: Diag Module

Code 4 - Air Injection System [AIR]faulty; Hot film Mass Air Flow Sensor
Code 6 - Idle Speed Control [ISC] faulty
Code 9 - Intake Air Temp [IAT] sensor open circuit

Check the harness in some key places to see if it's 'crumbling'
Regards . . . . JimF
'94 S500 Cpe

Visit my Mercedes Web Page
Reply With Quote
Old 10-13-2003, 12:44 PM
Registered User
Join Date: Jan 2001
Location: Northern Virginia
Posts: 46
thanks to Dale and Jim

Thanks a bunch to both of you for your help. I've got the feeling that some if not all of those codes may be a couple months old. I had the wiring harness and the throttle slide replaced (at MB's expense) about 5 months ago. I just got off the phone with my service advisor, and he could not tell me positively or not if the old codes had been cleared when they did the repairs, but did suggest that I check out the battery under a load test. Luckily i have acces to a load tester at the firehouse, and the battery did seem to need replacement. So....I have replaced the battery and cleared all the codes in the system with my little "reader". The ASR light is now out and doesn't come back on at I'm going to keep my fingers crossed and just recheck it in a few weeks......Thanks alot for your help.

BTW-what manual or doc did you guys get the codes list from...I've love to have a copy for future reference.

Reply With Quote
Old 10-13-2003, 06:37 PM
Posts: n/a
I use ALLDATA online.

Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On

All times are GMT -4. The time now is 08:36 AM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2018 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page