Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Search Forums
Reload this Page Search Results
Register ShopForum Gallery FAQ Calendar Today's Posts Search

Page 1 of 14 1 2311 Last »
Showing results 1 to 30 of 393
Search took 0.05 seconds. Search: Posts Made By: saumil
Forum: Tech Help 05-11-2016, 07:53 PM
Replies: 6
Views: 952
Posted By saumil
If clutch engages and is visually seen as turning...

If clutch engages and is visually seen as turning and there is no pressure difference between high and low sides (the ratio would likely be 6-7 or so), then it must be the compressor. To confirm that...
Forum: Tech Help 05-11-2016, 07:46 PM
Replies: 1
Views: 690
Posted By saumil
Small Ball Came Loose When Opening Lower Timing Chain Cover on 1987 260E

Hi,
We are doing a valve job on our 1987 260E with over 400K miles. Unfortunately, we were also trying to replace the chain and the chain dropped in the pan. So we had to open the lower timing...
Forum: Tech Help 10-05-2014, 12:20 PM
Replies: 17
Views: 2,317
Posted By saumil
Sorry, the link did not include the part, it is...

Sorry, the link did not include the part, it is this one:
Timing Chain Kit Brand: Febi Bilstein
Forum: Tech Help 10-05-2014, 12:18 PM
Replies: 17
Views: 2,317
Posted By saumil
This is what I have: 1987 Mercedes-Benz 260E...

This is what I have:

1987 Mercedes-Benz 260E Base Sedan - Camshafts & Timing Chains - Page 1 (http://www.pelicanparts.com/catalog/SuperCat/3218/MBZ_3218_ENGCAM_pg1.htm#item2)
Forum: Tech Help 10-05-2014, 12:15 PM
Replies: 17
Views: 2,317
Posted By saumil
The chain I have is a completely connected chain,...

The chain I have is a completely connected chain, there is no break (Febi). And because one end of the chain has dropped, I dont think I can do the chain linking/pulling trick. Is there another chain...
Forum: Tech Help 10-04-2014, 08:00 PM
Replies: 17
Views: 2,317
Posted By saumil
Liquiddog, even if the cover is off, do I still...

Liquiddog, even if the cover is off, do I still need to cut and crimp the new chain to put it in ?
Thanks
Forum: Tech Help 10-04-2014, 07:59 PM
Replies: 17
Views: 2,317
Posted By saumil
Thanks for the link to the service manual... I...

Thanks for the link to the service manual...
I now have all the steps to take the cover off...
Will try to get the cover off tomorrow.
Forum: Tech Help 10-04-2014, 06:29 PM
Replies: 17
Views: 2,317
Posted By saumil
Replace 1987 260E Timing Chain ?

Hi,
We had cut the timing chain link to replace the chain on my 1987 260E with over 400K miles. Accidently, one side of the chain dropped inside the lower cover. Presently my cylinder head is...
Forum: Tech Help 06-03-2013, 11:43 AM
Replies: 1
Views: 873
Posted By saumil
2001 E320 Factory Service Manual ?

Hi,
Does anyone know where can I find the factory service manual for a 2001 E320 ? A friend has to replace the evaporator in the car and will need directions to get to it.
Thanks,
Saumil
Forum: ML, GL, G-Wagen, R-Class, Unimog, Sprinter 07-02-2010, 08:33 PM
Replies: 5
Views: 2,327
Posted By saumil
Thanks you all, so I was wrong in suggesting my...

Thanks you all, so I was wrong in suggesting my friend not to buy these cars.

Saumil
Forum: ML, GL, G-Wagen, R-Class, Unimog, Sprinter 07-02-2010, 11:14 AM
Replies: 5
Views: 2,327
Posted By saumil
Revving up a ML320 or ML430 at idle ?

Hi,

One of my friend's is looking to buy a ML430 or a ML320. In couple of cars we saw, we were unable to rev up the engine beyond 4000 rpm at idle. I only had experience with my 260E which has no...
Forum: Tech Help 10-22-2009, 08:08 PM
Replies: 20
Views: 11,939
Posted By saumil
Huh... The plate is moving - I am not exactly...

Huh... The plate is moving - I am not exactly sure how the idle control valve modulates the air in the intake (some one else can help) BUT I would think that it would not involve changing the plate's...
Forum: Tech Help 10-21-2009, 08:13 PM
Replies: 20
Views: 11,939
Posted By saumil
Maybe the wiring to the idle switches is flaky or...

Maybe the wiring to the idle switches is flaky or the connector is not making a good contact with the posts.

When you turn on the ignition but before cranking, does the oxygen sensor light come on...
Forum: Tech Help 10-15-2009, 05:07 PM
Replies: 20
Views: 11,939
Posted By saumil
At idle, the voltage from the mass air sensor,...

At idle, the voltage from the mass air sensor, i.e the potentiometer should be around 0.7V. There are 3 terminals on it, one is ground, one is 12V and the third one should be at 0.7V (w.r.t. ground)....
Forum: Tech Help 09-30-2009, 11:40 PM
Replies: 23
Views: 3,423
Posted By saumil
You may have to ask Phil on Fastlane about the...

You may have to ask Phil on Fastlane about the exact location on your car. On fastlane, the sensor is under the fuel injection category and is called water temperature sensor.

I had the exact same...
Forum: Tech Help 09-30-2009, 11:04 PM
Replies: 23
Views: 3,423
Posted By saumil
Have you checked the coil ? I dont know about...

Have you checked the coil ? I dont know about this car, but in my car (87, 260E), very surprisingly the rough idling (sometimes at random), random stalling etc were all gone when I replaced the coil....
Forum: Tech Help 09-30-2009, 10:54 PM
Replies: 20
Views: 11,939
Posted By saumil
Actually, I just remembered, there are two...

Actually, I just remembered, there are two switches. One is on the throttle body and the other is near where the accelerator cable comes from. Check both.
Forum: Tech Help 09-30-2009, 10:52 PM
Replies: 20
Views: 11,939
Posted By saumil
Check the throttle linkage. There is a switch...

Check the throttle linkage. There is a switch that signals idle condition. I dont remember which way it works, but when on idle it is in one state (closed or open) and when the gas pedal is depressed...
Forum: Tech Help 09-30-2009, 10:43 PM
Replies: 0
Views: 951
Posted By saumil
1987 260E Transmission Upshift Problem...

Hi,

The automatic transmission on my 1987 260E has stopped shifting up.

Before this happened, for approx. a year, the transmission was sticking on 2nd and could upshift to 3 by releasing the...
Forum: Tech Help 01-30-2009, 07:55 PM
Replies: 12
Views: 2,323
Posted By saumil
did you check intake vaccum ? it could be on the...

did you check intake vaccum ? it could be on the exhaust side, catalytic converter...
Forum: Tech Help 09-27-2007, 09:19 PM
Replies: 2
Views: 855
Posted By saumil
If you tried a different push-button unit, and if...

If you tried a different push-button unit, and if the speed still does not modulate, the problem is likely with the blower motor regulator. Will have to get to the motor to confirm this, thats where...
Forum: Tech Help 09-27-2007, 09:13 PM
Replies: 15
Views: 2,448
Posted By saumil
What state is the malfunctioning tensioner in ?...

What state is the malfunctioning tensioner in ? If it is in a state that it is loose and wont let the regular size belt on, I may have an easier solution. Get a longer belt. The belt I have used and...
Forum: Tech Help 09-25-2007, 08:44 PM
Replies: 18
Views: 4,817
Posted By saumil
The power for the idle control valve comes via...

The power for the idle control valve comes via the OVP relay. A bad contact of the OVP relay in its socket can cause intermittent idle failure. Remove OVP relay, clean it properly, check that the...
Forum: Tech Help 09-25-2007, 08:40 PM
Replies: 4
Views: 851
Posted By saumil
You can test it before replacing too. You should...

You can test it before replacing too. You should get 10-11V on the terminals when you try to start the car. If you dont get this voltage, the problem could be with the fuel pump relay. Infact, it is...
Forum: Tech Help 09-22-2007, 11:43 PM
Replies: 2
Views: 913
Posted By saumil
Blower motor receives it power from the ignition...

Blower motor receives it power from the ignition switch so it should not "directly" affect the operation of the OVP relay or the fuel pump relay.

However, a bad blower motor can draw a lot of...
Forum: Tech Help 09-20-2007, 11:23 AM
Replies: 5
Views: 1,254
Posted By saumil
I am not sure a bad EHA would cause an instant...

I am not sure a bad EHA would cause an instant shutdown. EHA control is I think the only output from the ECU (fuel injection computer), and the car should run without the ECU control, without such...
Forum: Tech Help 09-18-2007, 12:15 PM
Replies: 30
Views: 5,192
Posted By saumil
Following up on a real good possibility suggested...

Following up on a real good possibility suggested by dpetryx,

You can check this:

Disconnect output lines to all the fuel injectors from the fuel distributor.

Bridge socket terminals...
Forum: Tech Help 09-18-2007, 12:02 PM
Replies: 20
Views: 2,800
Posted By saumil
Huh !! Did you say that the air was blowing OUT...

Huh !! Did you say that the air was blowing OUT of the vent under the wiper ? I have never checked this but I would think that the air would be sucked in rather than blown out. Did you rewire the...
Forum: Tech Help 09-17-2007, 10:19 PM
Replies: 5
Views: 1,254
Posted By saumil
Vaccum leak in the boot under the air sensor ?...

Vaccum leak in the boot under the air sensor ? General leaks in rubber hoses parts ? Spray carburettor cleaner to see if there is a change in RPM when sprayed at various intake areas such as injector...
Forum: Tech Help 09-17-2007, 09:57 PM
Replies: 20
Views: 2,800
Posted By saumil
What is the temp of the suction line (low...

What is the temp of the suction line (low pressure) where the service valve is ? Does it feel cold ? I am not sure that there should be such a large variation in suction pressure when you go from...
Showing results 1 to 30 of 393
Page 1 of 14 1 2311 Last »

 
Forum Jump


All times are GMT -4. The time now is 01:06 PM.

Contact Us - Mercedes-Benz Discussion Forum - Archive - Privacy Statement - Terms of Service - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page