Parts Catalog Accessories Catalog How To Articles Tech Forums
Call Pelican Parts at 888-280-7799
Shopping Cart Cart | Project List | Order Status | Help



Go Back   PeachParts Mercedes-Benz Forum > Mercedes-Benz Tech Information and Support > Tech Help

Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 11-20-2008, 07:07 PM
Registered User
 
Join Date: Nov 2008
Posts: 5
Angry cold start valve vs. ovp

I have read many threads about the same thing. And now its hapening to my 89 300e.
Low idle.
Stalls at lights.
Rough cold start
abs light on.
At first I was told that it could be the cold start valve and a few threads confirmed that that could be the issue. Now however I have seen some poastings that say it could be the ovp relay. This seams like it also be a likley problem ass well. Oh and the abs light is on.
I love my car and I want to fix her myself. However I dont have the money or time to fix phantom problems. And judging by some of the posts that I have read I dont want to trust a mcanic to fix my problems. or at least try fail and charge.
Hey you guyes colectivly know a hell of a lot more than me so any help would be much appreciated.

Reply With Quote
  #2  
Old 11-20-2008, 07:16 PM
Registered User
 
Join Date: Jul 2007
Location: USA
Posts: 2,156
There are some bulletins on this issue and I can tell you that most likely that you have 2 seperate problems. OVP can be tested with readily available tools. I can send you the document.
__________________
1986 300SDL, 211K,Dealership serviced its whole life
1991 190E 2.6(120k)
1983 300D(300k)
1977 300D(211k)
Reply With Quote
  #3  
Old 11-20-2008, 07:26 PM
Registered User
 
Join Date: Nov 2008
Posts: 5
sweet!

Ok thanks for the reply if you want you can e-mail the doc to me jke3e@yahoo.com
I dont know though I kinda hope its the ovp.
Reply With Quote
  #4  
Old 11-20-2008, 07:45 PM
Registered User
 
Join Date: Jul 2007
Location: USA
Posts: 2,156
for the stalling/Cold start:

1. no speed signal from the speedometer to the cise control unit
2.crankshaft postion sensor
3. EZL ignition system
4.electrical connections at ignition coil
5. Sockets of OVP and fuel pump relay bad solder connections
6. cise control unit
7. A/C compressor control unit
8. cold start valve
9. loose connections(grounds, cise wiring harness
10. Internal fuel leakage

had a similar problem on a 190E 2.6 and it turned out to be an internal fuel leakage problem. You may also have malfunction cise components
__________________
1986 300SDL, 211K,Dealership serviced its whole life
1991 190E 2.6(120k)
1983 300D(300k)
1977 300D(211k)
Reply With Quote
  #5  
Old 11-20-2008, 08:01 PM
Registered User
 
Join Date: Nov 2008
Posts: 5
Red face

Wow thanks man I apreciate the help. of the problems that you listed which would be simplest to fix? Im thinking like easy to hard you know?
Reply With Quote
  #6  
Old 11-20-2008, 08:12 PM
Registered User
 
Join Date: Jul 2007
Location: USA
Posts: 2,156
Quote:
Originally Posted by jk300e View Post
Wow thanks man I apreciate the help. of the problems that you listed which would be simplest to fix? Im thinking like easy to hard you know?
The easiest things to check are checking the OVP ,fuel pump relay, fuel hoses by visually inspecting them. The relays should have no loose sockets and connections. Also check the fuse in the OVP. Check the fuel hoses by looking carefully for cracks etc or gas smell on the hoses or the pumps. Also check the fuel pump cover for drip marks. Thats how I found my leak is by leaking at the cover and saw that they were drip marks that stood out from everything else. Alot spots on the cover light then I saw some dark spots which told me there was a leak there. The next thing would be to test the connections make sure everything is tight and not loose. Clean up ground connections. Then you could test continuity of the cise unit to the componets in the engine compartment by taking a dvom and measuring the resistance of the wires to and from the control unit. The wires should have .3 ohms or less of resistance.

the other things i didnt mention have test programs
__________________
1986 300SDL, 211K,Dealership serviced its whole life
1991 190E 2.6(120k)
1983 300D(300k)
1977 300D(211k)
Reply With Quote
  #7  
Old 11-20-2008, 08:17 PM
Registered User
 
Join Date: Nov 2008
Posts: 5
Talking thank you

Hey I got an early call tomorrow but after work I will be under the hood I will kep you posted on my progress. Thaks a lot!
Reply With Quote
  #8  
Old 11-20-2008, 08:50 PM
slk230red's Avatar
WECO Installer
 
Join Date: Jul 2006
Location: Tampa, FL
Posts: 820
Quote:
Originally Posted by jk300e View Post
I have read many threads about the same thing. And now its hapening to my 89 300e.
Low idle.
Stalls at lights.
Rough cold start
abs light on.
At first I was told that it could be the cold start valve and a few threads confirmed that that could be the issue. Now however I have seen some poastings that say it could be the ovp relay. This seams like it also be a likley problem ass well. Oh and the abs light is on.
I love my car and I want to fix her myself. However I dont have the money or time to fix phantom problems. And judging by some of the posts that I have read I dont want to trust a mcanic to fix my problems. or at least try fail and charge.
Hey you guyes colectivly know a hell of a lot more than me so any help would be much appreciated.

If the ABS light stays on, check the OVP relay. First, check the fuse on top of the OVP relay. Also, check that the OVP relay is fully seated into the socket. If problem still exists, then you will probably need to replace the relay.

To bench test: Ground on 31 and Battery on 15, relay operates. Then, with battery applied to 30, 12v should appear on pin 87E and 87L.



__________________

1993 190E 2.3
2001 SLK230
1971 LS5 (454) Corvette Convertible
Reply With Quote
  #9  
Old 11-21-2008, 12:04 AM
wbain5280's Avatar
Registered User
 
Join Date: May 2001
Location: Northern Va.
Posts: 3,386
The OVP supplies power to the ECU and the ABS computer. The car will run badly if the ECU is not on. As said previously, check the fuse on top of the OVP. If it's good, and you can check with an ohmmeter, take the relay out and remove the case. Resolder the connections at the bottom, put the case back on and plug it in. There is no cost for doing this and will save you some money. If this does not work, get a new OVP.
__________________
Regards

Warren

Currently 1965 220Sb, 2002 FORD Crown Vic Police Interceptor

Had 1965 220SEb, 1967 230S, 280SE 4.5, 300SE (W126), 420SEL

ENTER > = (HP RPN)

Not part of the in-crowd since 1952.
Reply With Quote
  #10  
Old 12-04-2008, 08:26 AM
Registered User
 
Join Date: Nov 2008
Location: Oklahoma City
Posts: 1
My 95 E320 just started doing the samething. It died a few times at start up, is running like crap, doesn;t have a steady smooth idle, and the abs light comes on. I bought this car as a project and have replaced all of the normal issues with this model except replacing the OVP.
Reply With Quote
  #11  
Old 12-04-2008, 09:09 AM
babymog's Avatar
Loose Cannon - No Balls
 
Join Date: Jan 2006
Location: Northeast Indiana
Posts: 10,765
Start with the OVP. It's $65 for a new one on-line, and from reading here: if it isn't bad, it will be. I ordered one for a spare and have had a bad one in one of my diesels, I'm a believer.

The ABS light with the bad running is almost a sure sign.
__________________

Gone to the dark side

- Jeff
Reply With Quote
  #12  
Old 12-04-2008, 01:36 PM
Registered User
 
Join Date: Oct 2004
Posts: 4,177
FWIW, I've been a professoinal MB tech for 12 years and have never replaced a cold start valve on a 103 engine. They just don't go bad.
__________________

90 300TE 4-M
Turbo 103, T3/T04E 50 trim
T04B cover .60 AR
Stage 3 turbine .63 AR
A2W I/C, 40 LB/HR
MS2E, 60-2 Direct Coil Control
3" Exh, AEM W/B O2
Underdrive Alt. and P/S Pulleys,
Vented Rear Discs, .034 Booster.
3.07 diffs 1st Gear Start

90 300CE
104.980
Milled & ported head, 10.3:1 compression
197° intake cam w/20° advancer
Tuned CIS ECU
4° ignition advance
PCS TCM2000, built 722.6
600W networked suction fan
Sportline sway bars
V8 rear subframe, Quaife ATB 3.06 diff
Reply With Quote
  #13  
Old 12-04-2008, 01:56 PM
pawoSD's Avatar
Dieselsüchtiger
 
Join Date: Oct 2004
Location: Grand Rapids, MI
Posts: 15,438
Quote:
Originally Posted by duxthe1 View Post
FWIW, I've been a professoinal MB tech for 12 years and have never replaced a cold start valve on a 103 engine. They just don't go bad.
Then why do they seem to have such a hard time cold starting and idling?? (Maybe I am just bitter....)
__________________
-diesel is not just a fuel, its a way of life-
'15 GLK250 Bluetec 118k - mine - (OC-123,800)
'17 Metris(VITO!) - 37k - wifes (OC-41k)
'09 Sprinter 3500 Winnebago View - 62k (OC - 67k)
'13 ML350 Bluetec - 95k - dad's (OC-98k)
'01 SL500 - 103k(km) - dad's (OC-110,000km)
'16 E400 4matic Sedan - 148k - Brothers (OC-155k)
Reply With Quote
  #14  
Old 12-04-2008, 10:35 PM
Registered User
 
Join Date: Jul 2007
Location: USA
Posts: 2,156
Quote:
Originally Posted by pawoSD View Post
Then why do they seem to have such a hard time cold starting and idling?? (Maybe I am just bitter....)
Just thought I would pass this along, make sure you have spark plugs with a heat range of 145 installed.

Bosch part number bosch H 9 DC or bosch H 9 DCO
__________________
1986 300SDL, 211K,Dealership serviced its whole life
1991 190E 2.6(120k)
1983 300D(300k)
1977 300D(211k)
Reply With Quote
  #15  
Old 12-04-2008, 11:43 PM
Registered User
 
Join Date: Oct 2004
Posts: 4,177
"Then why do they seem to have such a hard time cold starting and idling?? (Maybe I am just bitter....) "



The cold start valve is a very simple part of a complex system. There is a reason the newer cars don't have CIS injection. Most manufacturers gave up on it well before Mercedes did.

__________________

90 300TE 4-M
Turbo 103, T3/T04E 50 trim
T04B cover .60 AR
Stage 3 turbine .63 AR
A2W I/C, 40 LB/HR
MS2E, 60-2 Direct Coil Control
3" Exh, AEM W/B O2
Underdrive Alt. and P/S Pulleys,
Vented Rear Discs, .034 Booster.
3.07 diffs 1st Gear Start

90 300CE
104.980
Milled & ported head, 10.3:1 compression
197° intake cam w/20° advancer
Tuned CIS ECU
4° ignition advance
PCS TCM2000, built 722.6
600W networked suction fan
Sportline sway bars
V8 rear subframe, Quaife ATB 3.06 diff
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On




All times are GMT -4. The time now is 12:28 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Search Engine Optimization by vBSEO 3.6.0
Copyright 2024 Pelican Parts, LLC - Posts may be archived for display on the Peach Parts or Pelican Parts Website -    DMCA Registered Agent Contact Page