|
|
|
#1
|
|||
|
|||
Motor mount bolt MIA
Anyone know the size and thread of the 8mm center motor mount bolt? Mercedes 300d 1985
|
#2
|
||||
|
||||
Get vin and take it to dealer and purchase the proper fastener. I can't imagine it being over about $5. Pretty sure you won't find the correct fastener at Home Depot.
__________________
Jim |
#3
|
|||
|
|||
Closest Mercedes dealer is about 2 hour drive from me is the only Thing lol
|
#4
|
|||
|
|||
disom93, call a MB dealer and have them mail/ship the bolt to you, or go to a salvage yard ... which will entail a lot of work for a low cost item.
__________________
Fred Hoelzle |
#5
|
||||
|
||||
If you are talking about the small bolts that fit into the underside of the mount itself - through the cross member then I am pretty sure they are of 8.8 strength (minimum for these cars) and are of standard coarse metric thread what ever the size is.
If, however, you are talking about the bolts that hold the cross member to the chassis then I think they are 10.9 strength and could be a fine thread - I can't remember the specifications for sure. Use my uncertain information with caution! Do not cross thread or try to use the wrong thread!
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior Don't leave that there - I'll take it to bits! |
#6
|
||||
|
||||
They have some hex bolts at Home Depot but not many. Probably none that size. You could take it to Home Depot to determine the length and thread size/pitch then order it online from Fastenal.
__________________
Current: 1975 450SEL, 83 300D, 88 Yugo GVX, 90 300D OM603 swap, 91 F150 4.6 4v swap, 93 190E Sportline LE 3.0L M104 swap, 93 190E Sportline LE Megasquirt, 03 Sprinter, 06 E500 4Matic wagon. |
#7
|
||||
|
||||
Bolts (If We're going UNKNOWN)
Metric
Try any Ace Hardware,they usually have a good selection!
__________________
'84 300SD sold 124.128 |
#8
|
|||
|
|||
I just didn't have the one to try it's missing not sure where it went so was needing an idea of what to order
|
#9
|
|||
|
|||
And yes it's the one coming from bottom thru the center
|
#10
|
|||
|
|||
10x1.50 or 10x 1.75
|
#11
|
|||
|
|||
disom93, describe the location of the bolt to the MB Parts Department rep and he will check the parts diagram for your car to provide the proper bolt. If you have never gone to a MB Parts Department, with the VIN for a car they can look up any part for any MB vehicle. That eliminates any guess work, or wondering if you are going to get the correct part.
__________________
Fred Hoelzle Last edited by Ferdman; 11-25-2015 at 05:17 AM. |
#12
|
|||
|
|||
Ok I called dealer they can get the bolt but they didn't know the size I guess I'll pull the other side one out and just take it to the store with me to see thanks for the help
|
#13
|
|||
|
|||
__________________
|
#14
|
||||
|
||||
$20 for a bolt like that is one of the many, many reasons I have ceased even calling Pelican
My PnP posts that screws are a dime each. Sure better than the screwing pelican wants to give us.
__________________
1985 300D 198K sold 1982 300D 202K 1989 300E 125K 1992 940T "If you dont have time to do it safely, you dont have time to do it" "The democracy will cease to exist when you take away from those who are willing to work and give to those who would not." |
#15
|
|||
|
|||
Quote:
Here is a used one on ebay as well.. 1985 Mercedes 300D Engine Mount Bolt | eBay
__________________
|
Bookmarks |
|
|