|
|
|
#1
|
||||
|
||||
Rebuilding Driveshaft
OK Folks,
I need some help here with two projects. Can someone give me a blow-by-blow description on how to rebuild the driveshaft, as well as replace the motor mounts, including the size of the wrenches I will need? Mucho Thanks, Torie
__________________
1983 300D, the "Avocado" 1976 240D, 4-spd the "Pumpkin", SOLD to Pierre 1984 190D, 2.2L, 5-spd, my intro to MBZ diesels, crashed into in 2002 |
#2
|
||||
|
||||
Hi Torie,
Are we talking W115, W123 or W201 here (says he looking at the stable listed in your sig)?
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior Don't leave that there - I'll take it to bits! |
#3
|
||||
|
||||
1983 300D
It's the turbo diesel (Taxi model) 300D, 1983.
Thanks, Army. Torie
__________________
1983 300D, the "Avocado" 1976 240D, 4-spd the "Pumpkin", SOLD to Pierre 1984 190D, 2.2L, 5-spd, my intro to MBZ diesels, crashed into in 2002 |
#5
|
||||
|
||||
Forgot to mention, the reason for the driveline work, is to replace the carrier bearing. I believe the U-joint is fine at this point, but am sure will go out also if I don't replace the bearing and flexjoints soon. Keeping it parked til I do the driveline and mounts.
__________________
1983 300D, the "Avocado" 1976 240D, 4-spd the "Pumpkin", SOLD to Pierre 1984 190D, 2.2L, 5-spd, my intro to MBZ diesels, crashed into in 2002 |
#6
|
||||
|
||||
Quote:
I have mentioned this a few times before that everyone seems to have their own idea what "rebuilt" means. Even what I did when I replaced the U-joint is not a rebuilt Drive Shaft; because it did not include balancing it.
__________________
84 300D, 82 Volvo 244Gl Diesel |
#7
|
|||
|
|||
Remember, flex disks stay with the drive shaft. That will help you figure out what bolts to remove. There is a bushing in each end. You may need to drill a hole through it and put a bolt/drill bit.whatever through it to remove.
Mark the drive shaft halves so you can index them correctly relative to each other. The shafts are marked from the factory but there is no telling what a PO has done to it. Noting how the carrier bearing is oriented before you remove it will save you some time figuring it out
__________________
85SD 240K & stopped counting painted, putting bac together. 84SD 180,000. sold to a neighbor and member here but I forget his handle. The 84 is much improved from when I had it. 85TD beginning to repair to DD status. Lots of stuff to do. |
#8
|
|||
|
|||
Make the job go easy. Drop the diff 6” . Just 4 bolts into the body above and behind the diff. Use a floor jack to lower easy. This saves having to use a pry bar to clear the centering pilot past the yoke.
Don’t hammer the bearing off. Get a long reach puller. Even a cheap one will work. Go to a plumbing shop and scrounge a scrap of pipe about 8” x just enough to slip over the spline. Use this to hammer the new bearing and keeper disk into the seat. What ever you do never put the universal joint in a vice. I saw this done at a MB dealer shop. What some people will do to sell a new drive shaft. If the car drives smooth now the shaft halves is in the correct orientation. Do what ever you must to guarantee the halves go back in the same place. Punch some marks as close to gether as possible as the factory marks are sort of vague. I guess every guy on the board has done this job or will do sooner or later. It gets easier every time. Enjoy.
__________________
1984 300SD turbo 126 "My true love" God made me an atheist and who am I to question His wisdom |
#9
|
||||
|
||||
I think the drive shaft uses a 42mm hex or two. My 124 uses 19mm nuts and bolts on the flex discs. I think then123 is the same.
All you need to do is just replace the flex discs, easy, and the carrier bearing. The u joint is not serviceable by the normal DIY person. |
#10
|
||||
|
||||
Quote:
X2 on marking things.
__________________
84 300D, 82 Volvo 244Gl Diesel |
#11
|
||||
|
||||
I think this might have been posted already but they way in which these html links are now displayed I sometimes wonder!
PeachPartsWiki: Driveshaft Support (carrier) Bearing Replacement One thing that hasn't been mentioned in this thread (so far - so now I'm going to do it!) is to mark the positions of the propshafts before you take them apart. I used to think that this was one of the most vital stages to the job - however there was a thread (which I'll try and find) where certain information in the FSM came to light which basically says Quote:
__________________
1992 W201 190E 1.8 171,000 km - Daily driver 1981 W123 300D ~ 100,000 miles / 160,000 km - project car stripped to the bone 1965 Land Rover Series 2a Station Wagon CIS recovery therapy! 1961 Volvo PV544 Bare metal rat rod-ish thing I'm here to chat about cars and to help others - I'm not here "to always be right" like an internet warrior Don't leave that there - I'll take it to bits! |
Bookmarks |
|
|